以上為資料預覽概圖，下載文件后為壓縮包資料文件。【清晰，無水印，可編輯】dwg后綴為cad圖，doc后綴為word格式，需要請自助下載即可，有疑問可以咨詢QQ 197216396 或 11970985
原文：
題目 Introduciton of Machining
Have a shape as a processing method, all machining process for the production of the most commonly used and most important method. Machining process is a process generated shape, in this process, Drivers device on the workpiece material to be in the form of chip removal. Although in some occasions, the workpiece under no circumstances, the use of mobile equipment to the processing, However, the majority of the machining is not only supporting the workpiece also supporting tools and equipment to complete.
Machining know the process has two aspects. Small group of low-cost production. For casting, forging and machining pressure, every production of a specific shape of the workpiece, even a spare parts, almost have to spend the high cost of processing. Welding to rely on the shape of the structure, to a large extent, depend on effective in the form of raw materials. In general, through the use of expensive equipment and without special processing conditions, can be almost any type of raw materials, mechanical processing to convert the raw materials processed into the arbitrary shape of the structure, as long as the external dimensions large enough, it is possible. Because of a production of spare parts, even when the parts and structure of the production batch sizes are suitable for the original casting, Forging or pressure processing to produce, but usually prefer machining.
Strict precision and good surface finish, Machining the second purpose is the establishment of the high precision and surface finish possible on the basis of. Many parts, if any other means of production belonging to the large-scale production, Well Machining is a low-tolerance and can meet the requirements of small batch production. Besides, many parts on the production and processing of coarse process to improve its general shape of the surface. It is only necessary precision and choose only the surface machining. For instance, thread, in addition to mechanical processing, almost no other processing method for processing. Another example is the blacksmith pieces keyhole processing, as well as training to be conducted immediately after the mechanical completion of the processing.
Primary Cutting Parameters
Cutting the work piece and tool based on the basic relationship between the following four elements to fully describe : the tool geometry, cutting speed, feed rate, depth and penetration of a cutting tool.
Cutting Tools must be of a suitable material to manufacture, it must be strong, tough, hard and wear-resistant. Tool geometry -- to the tip plane and cutter angle characteristics -- for each cutting process must be correct.
Cutting speed is the cutting edge of work piece surface rate, it is inches per minute to show. In order to effectively processing, and cutting speed must adapt to the level of specific parts -- with knives. Generally, the more hard work piece material, the lower the rate.
Progressive Tool to speed is cut into the work piece speed. If the work piece or tool for rotating movement, feed rate per round over the number of inches to the measurement. When the work piece or tool for reciprocating movement and feed rate on each trip through the measurement of inches. Generally, in other conditions, feed rate and cutting speed is inversely proportional to。
Depth of penetration of a cutting tool -- to inches dollars -- is the tool to the work piece distance. Rotary cutting it to the chip or equal to the width of the linear cutting chip thickness. Rough than finishing, deeper penetration of a cutting tool depth.
Wears of Cutting Tool
We already have been processed and the rattle of the countless cracks edge tool, we learn that tool wear are basically three forms : flank wear, the former flank wear and V-Notch wear. Flank wear occurred in both the main blade occurred vice blade. On the main blade, shoulder removed because most metal chip mandate, which resulted in an increase cutting force and cutting temperature increase, If not allowed to check, That could lead to the work piece and the tool vibration and provide for efficient cutting conditions may no longer exist. Vice-bladed on, it is determined work piece dimensions and surface finish. Flank wear size of the possible failure of the product and surface finish are also inferior. In most actual cutting conditions, as the principal in the former first deputy flank before flank wear, wear arrival enough, Tool will be effective, the results are made unqualified parts.
As Tool stress on the surface uneven, chip and flank before sliding contact zone between stress, in sliding contact the start of the largest, and in contact with the tail of zero, so abrasive wear in the region occurred. This is because the card cutting edge than the nearby settlements near the more serious wear, and bladed chip due to the vicinity of the former flank and lost contact wear lighter. This results from a certain distance from the cutting edge of the surface formed before the knife point Ma pit, which is usually considered before wear. Under normal circumstances, this is wear cross-sectional shape of an arc. In many instances and for the actual cutting conditions, the former flank wear compared to flank wear light, Therefore flank wear more generally as a tool failure of scale signs. But because many authors have said in the cutting speed of the increase, Maeto surface temperature than the knife surface temperatures have risen faster. but because any form of wear rate is essentially temperature changes by the significant impact. Therefore, the former usually wear in high-speed cutting happen.
The main tool flank wear the tail is not processed with the work piece surface in contact, Therefore flank wear than wear along with the ends more visible, which is the most common. This is because the local effect, which is as rough on the surface has hardened layer, This effect is by cutting in front of the hardening of the work piece. Not just cutting, and as oxidation skin, the blade local high temperature will also cause this effect. This partial wear normally referred to as pit sexual wear, but occasionally it is very serious. Despite the emergence of the pits on the Cutting Tool nature is not meaningful impact, but often pits gradually become darker If cutting continued the case, then there cutter fracture crisis.
If any form of sexual allowed to wear, eventually wear rate increase obviously will be a tool to destroy failure destruction, that will no longer tool for cutting, cause the work piece scrapped, it is good, can cause serious damage machine. For various carbide cutting tools and for the various types of wear, in the event of a serious lapse, on the tool that has reached the end of the life cycle. But for various high-speed steel cutting tools and wear belonging to the non-uniformity of wear, has been found : When the wear and even to allow for a serious lapse, the most meaningful is that the tool can re-mill use, of course, In practice, cutting the time to use than the short time lapse. Several phenomena are one tool serious lapse began features : the most common is the sudden increase cutting force, appeared on the work piece burning ring patterns and an increase in noise.
The Effect of Changes in Cutting Parameters on Cutting Temperatures
In metal cutting operations heat is generated in the primary and secondary deformation zones and this results in a complex temperature distribution throughout the tool, workpiece and chip. A typical set of isotherms is shown in figure where it can be seen that, as could be expected, there is a very large temperature gradient throughout the width of the chip as the workpiece material is sheared in primary deformation and there is a further large temperature in the chip adjacent to the face as the chip is sheared in secondary deformation. This leads to a maximum cutting temperature a short distance up the face from the cutting edge and a small distance into the chip.
Since virtually all the work done in metal cutting is converted into heat, it could be expected that factors which increase the power consumed per unit volume of metal removed will increase the cutting temperature. Thus an increase in the rake angle, all other parameters remaining constant, will reduce the power per unit volume of metal removed and cutting temperatures will reduce. When considering increase in undeformed chip thickness and cutting speed the situation is more comples. An increase in undeformed chip thickness and cutting speed the situation is more complex. An increase in undeformed chip thickness tends to be a scale effect where the amounts of heat which pass to the workpiece, the tool and chip remain in fixed proportions and the changes in cutting temperature tend to be small. Increase in cutting speed, however, reduce the amount of heat which passes into the workpiece and this increase the temperature rise of the chip in primary deformation. Further, the secondary deformation zone tends to be smaller and this has the effect of increasing the temperatures in this zone. Other changes in cutting parameters have virtually no effect on the power consumed per unit volume of metal removed and consequently have virtually no effect on the power consumed per unit volume of metal removed and consequently have virtually no effect on the cutting temperatures. Since it has been shown that even small changes in cutting temperature have a significant effect on tool wear rate, it is appropriate to indicate how cutting temperatures can be assessed from cutting data.
The most direct and accurate method for measuring temperatures in high-speed-steel cutting tools is that of Wright&Trent which also yields detailed information on temperature distributions in high-speed-steel tools which relates microstructural changes to thermal history.
Trent has described measurements of cutting temperatures and temperature distributions for high-speed-steel tools when machining a wide range of workpiece materials. This technique has been further developed by using scanning electron microscopy to study fine-scale microstructural changes srising from over tempering of the tempered martensitic matrix of various high-speed-steels. This technique has also been used to study temperature distributions in both high-speed-steel single point turning tools and twist drills.
Automatic Fixture Design
Assembly equipment used in the traditional synchronous fixture put parts of the fixture mobile center, to ensure that components from transmission from the plane or equipment plate placed after removal has been scheduled for position. However, in certain applications, mobile mandatory parts of the center line, it may cause parts or equipment damage. When parts vulnerability and may lead to a small vibration abandoned, or when their location is by machine spindle or specific to die, Tolerance again or when the request is a sophisticated, it would rather let the fixture to adapt to the location of parts, and not the contrary. For these tasks, Elyria, Ohio, the company has developed Zaytran a general non-functional data synchronization West category FLEXIBILITY fixture. Fixture because of the interaction and synchronization devices is independent, The synchronous device can use sophisticated equipment to replace the slip without affecting the fixture force. Fixture specification range from 0.2 inches itinerary, 5 pounds clamping force of the six-inch trip, 400-inch clamping force.
The characteristics of modern production is becoming smaller and smaller quantities and product specifications biggest changes. Therefore, in the final stages of production, assembly of production, quantity and product design changes appear to be particularly vulnerable. This situation is forcing many companies to make greater efforts to rationalize the extensive reform and the previously mentioned case of assembly automation. Despite flexible fixture behind the rapid development of flexible transport and handling devices, such as backward in the development of industrial robots, it is still expected to increase the flexibility fixture. In fact the important fixture devices -- the production of the devices to strengthen investment on the fixture so that more flexibility in economic support holders.
According to their flexibility and fixture can be divided into : special fixture, the fixture combinations, the standard fixture, high flexible fixture. Flexible fixture on different parts of their high adaptability and the few low-cost replacement for the characteristic.
Forms can transform the structure of the flexible fixture can be installed with the change of structure components (such as needle cheek plate, Multi-chip components and flake cheek plate), a non-standard work piece gripper or clamping elements (for example : commencement standard with a clamping fixture and mobile components fixture supporting documents), or with ceramic or hardening of the intermediary substances (such as : Mobile particle bed fixture and heat fixture tight fixture). To production, the parts were secured fixture, the need to generate clamping function, its fixture with a few unrelated to the sexual submissive steps :
According to the processing was part of that foundation and working characteristics to determine the work piece fixture in the required position, then need to select some stability flat combination, These constitute a stable plane was fixed in the work piece fixture set position on the clamp-profile structure, all balanced and torque, it has also ensured that the work features close to the work piece. Finally, it must be calculated and adjusted, assembly or disassembly be standard fixture components required for the position, so that the work piece firmly by clamping fixture in China. In accordance with this procedure, the outline fixture structure and equipped with the planning and recording process can be automated control.
Structural modeling task is to produce some stable flat combination, Thus, these plane of the work pieces clamping force and will fixture stability. According to usual practice, this task can be human-machine dialogue that is almost completely automated way to completion. A man-machine dialogue that is automated fixture structure modeling to determine the merits can be conducted in an organized and planning fixture design, reduce the amount of the design, shortening the study period and better distribution of work conditions. In short, can be successfully achieved significantly improve fixture efficiency and effectiveness.
Fully prepared to structure programs and the number of material circumstances, the completion of the first successful assembly can save up to 60% of the time.
Therefore fixture process modeling agencies is the purpose of the program have appropriate documents.
譯文：
題目 加工基礎
機械加工是所有制造過程中最普遍使用的而且是最重要的方法。機械加工過程是一個產生形狀的過程，在這過程中，驅動裝置使工件上的一些材料以切屑的形式被去除。盡管在某些場合，工件無承受情況下，使用移動式裝備來實現加工，但大多數的機械加工是通過既支承工件又支承刀具的裝備來完成。
機械加工在知道過程中具備兩方面。小批生產低費用。對于鑄造、鍛造和壓力加工，每一個要生產的具體工件形狀，即使是一個零件，幾乎都要花費高額的加工費用。靠焊接來產生的結構形狀，在很大程度上取決于有效的原材料的形式。一般來說，通過利用貴重設備而又無需特種加工條件下，幾乎可以以任何種類原材料開始，借助機械加工把原材料加工成任意所需要的結構形狀，只要外部尺寸足夠大，那都是可能的。因此對于生產一個零件，甚至當零件結構及要生產的批量大小上按原來都適于用鑄造、鍛造或者壓力加工來生產的，但通常寧可選擇機械加工。
嚴密的精度和良好的表面光潔度，機械加工的第二方面用途是建立在高精度和可能的表面光潔度基礎上。許多零件，如果用別的其他方法來生產屬于大批量生產的話，那么在機械加工中則是屬于低公差且又能滿足要求的小批量生產了。另方面，許多零件靠較粗的生產加工工藝提高其一般表面形狀，而僅僅是在需要高精度的且選擇過的表面才進行機械加工。例如內螺紋，除了機械加工之外，幾乎沒有別的加工方法能進行加工。又如已鍛工件上的小孔加工，也是被鍛后緊接著進行機械加工才完成的。
基本的機械加工參數
切削中工件與刀具的基本關系是以以下四個要素來充分描述的：刀具的幾何形狀，切削速度，進給速度，和吃刀深度。
切削刀具必須用一種合適的材料來制造，它必須是強固、韌性好、堅硬而且耐磨的。刀具的幾何形狀——以刀尖平面和刀具角為特征——對于每一種切削工藝都必須是正確的。切削速度是切削刃通過工件表面的速率，它是以每分鐘英寸來表示。為了有效地加工，切削速度高低必須適應特定的工件——刀具配合。一般來說，工件材料越硬，速度越低。進給速度是刀具切進工件的速度。若工件或刀具作旋轉運動，進給量是以每轉轉過的英寸數目來度量的。當?shù)毒呋蚬ぜ魍鶑?fù)運動時，進給量是以每一行程走過的英寸數度量的。一般來說，在其他條件相同時，進給量與切削速度成反比。
吃刀深度——以英寸計——是刀具進入工件的距離。它等于旋削中的切屑寬度或者等于線性切削中的切屑的厚度。粗加工比起精加工來，吃刀深度較深。
切削參數的改變對切削溫度的影響
金屬切削操作中，熱是在主變形區和副變形區發生的。這結果導致復雜的溫度分布遍及刀具、工件和切屑。圖中顯示了一組典型等溫曲線，從中可以看出：像所能預料的那樣，當工件材料在主變形區被切削時，沿著整個切屑的寬度上有著很大的溫度梯度，而當在副變形區，切屑被切落時，切屑附近的前刀面上就有更高的溫度。這導致了前刀面和切屑離切削刃很近的地方切削溫度較高。
實質上由于在金屬切削中所做的全部功能都被轉化為熱，那就可以預料：被切離金屬的單位體積功率消耗曾家的這些因素就將使切削溫度升高。這樣刀具前角的增加而所有其他參數不變時，將使切離金屬的單位體積所耗功率減小，因而切削溫度也將降低。當考慮到未變形切屑厚度增加和切削速度，這情形就更是復雜。未變形切屑厚度的增加趨勢必導致通過工件的熱的總數上產生比例效應，刀具和切屑仍保持著固定的比例，而切削溫度變化傾向于降低。然而切削速度的增加，傳導到工件上的熱的數量減少而這又增加主變形區中的切屑溫升。進而副變形區勢必更小，這將在該區內產生升溫效應。其他切削參數的變化，實質上對于被切離的單位體積消耗上并沒有什么影響，因此實際上對切削溫度沒有什么作用。因?yàn)槭聦?shí)已經表明：切削溫度即使有小小的變化對刀具磨損率都將有實質意義的影響作用。這表明如何人從切削參數來確定切削溫度那是很合適的。
為著測定高速鋼刀具溫度的最直接和最精確的方法是W&T法，這方法也就是可提供高速鋼刀具溫度分布的詳細信息的方法。該項技術是建立在高速鋼刀具截面金相顯微測試基礎上，目的是要建立顯微結構變化與熱變化規律圖線關系式。當要加工廣泛的工件材料時，Trent已經論述過測定高速鋼刀具的切削溫度及溫度分布的方法。這項技術由于利用電子顯微掃描技術已經進一步發展，目的是要研究將已回過火和各種馬氏體結構的高速鋼再回火引起的微觀顯微結構變化情況。這項技術亦用于研究高速鋼單點車刀和麻花鉆的溫度分布。
刀具磨損
從已經被處理過的無數脆裂和刃口裂紋的刀具中可知，刀具磨損基本上有三種形式：后刀面磨損，前刀面磨損和V型凹口磨損。后刀面磨損既發生在主刀刃上也發生副刀刃上。關于主刀刃，因其擔負切除大部金屬切屑任務，這就導致增加切削力和提高切削溫度，如果聽任而不加以檢查處理，那可能導致刀具和工件發生振動且使有效切削的條件可能不再存在。關于副刀刃，那是決定著工件的尺寸和表面光潔度的，后刀面磨損可能造成尺寸不合格的產品而且表面光潔度也差。在大多數實際切削條件下，由于主前刀面先于副前刀面磨損，磨損到達足夠大時，刀具將實效，結果是制成不合格零件。
由于刀具表面上的應力分布不均勻，切屑和前刀面之間滑動接觸區應力，在滑動接觸區的起始處最大，而在接觸區的尾部為零，這樣磨蝕性磨損在這個區域發生了。這是因?yàn)樵谇邢骺ㄗ^(qū)附近比刀刃附近發生更嚴重的磨損，而刀刃附近因切屑與前刀面失去接觸而磨損較輕。這結果離切削刃一定距離處的前刀面上形成麻點凹坑，這些通常被認為是前刀面的磨損。通常情況下，這磨損橫斷面是圓弧形的。在許多情況中和對于實際的切削狀況而言，前刀面磨損比起后刀面磨損要輕，因此后刀面磨損更普遍地作為刀具失效的尺度標志。然而因許多作者已經表示過的那樣在增加切削速度情況下，前刀面上的溫度比后刀面上的溫度升得更快，而且又因任何形式的磨損率實質上是受到溫度變化的重大影響。因此前刀面的磨損通常在高速切削時發生的。
刀具的主后刀面磨損帶的尾部是跟未加工過的工件表面相接觸，因此后刀面磨損比沿著磨損帶末端處更為明顯，那是最普通的。這是因?yàn)榫植啃?yīng)，這像未加工表面上的已硬化層，這效應是由前面的切削引起的工件硬化造成的。不只是切削，還有像氧化皮，刀刃產生的局部高溫也都會引起這種效應。這種局部磨損通常稱作為凹坑性磨損，而且偶爾是非常嚴重的。盡管凹坑的出現對刀具的切削性質無實質意義的影響，但凹坑常常逐漸變深，如果切削在繼續進行的話，那么刀具就存在斷裂的危機。
如果任何進行性形式 的磨損任由繼續發展，最終磨損速率明顯地增加而刀具將會有摧毀性失效破壞，即刀具將不能再用作切削，造成工件報廢，那算是好的，嚴重的可造成機床破壞。對于各種硬質合金刀具和對于各種類型的磨損，在發生嚴重失效前，就認為已達到刀具的使用壽命周期的終點。然而對于各種高速鋼刀具，其磨損是屬于非均勻性磨損，已經發現：當其磨損允許連續甚至到嚴重失效開始，最有意義的是該刀具可以獲得重磨使用，當然，在實際上，切削時間遠比使用到失效的時間短。以下幾種現象之一均是刀具嚴重失效開始的特征：最普遍的是切削力突然增加，在工件上出現燒損環紋和噪音嚴重增加等。
自動夾具設計
用做裝配設備的傳統同步夾具把零件移動到夾具中心上，以確保零件從傳送機上或從設備盤上取出后置于已定位置上。然而在某些應用場合、強制零件移動到中心線上時，可能引起零件或設備破壞。當零件易損，而且小小振動可能導致報廢時，或當其位置是由機床主軸或模具來具體時，再或者當公差要求很精密時，那寧可讓夾具去適應零件位置，而不是相反。為著這些工作任務，美國俄亥俄州Elyria的Zaytran公司已經開發了一般性功能數據的非同步西類柔順性夾具。因?yàn)閵A具作用力和同步化裝置是各自獨立的，該同步裝置可以用精密的滑移裝置來替換而不影響夾具作用力。夾具規格范圍是從0.2英寸行程，5英鎊夾緊力到6英寸行程、400英寸夾緊力。
現代生產的特征是批量變得越來越小而產品的各種規格變化最大。因此，生產的最后階段，裝配因生產計劃、批量和產品設計的變更而顯得特別脆弱。這種情形正迫使許多公司更多地致力于廣泛的合理化改革和前面提到過情況那樣裝配自動化。盡管柔性夾具的發展很快落后與柔性運輸處理裝置的發展，如落后于工業機器人的發展，但仍然試圖指望增加夾具的柔順性。事實上夾具的重要的裝置——生產裝置的專向投資就加強了使夾具更加柔性化在經濟上的支持。
根據它們?nèi)犴樞?，夾具可以分為：專用夾具、組合夾具、標準夾具、高柔性夾具。柔性夾具是以它們對不同工件的高適應性和以少更換低費用為特征的。
結構形式可變換的柔性夾具裝有可變更結構排列的零件（例如針形頰板，多片式零件和片狀頰板），標準工件的非專用夾持或夾緊元件（例如：啟動標準夾持夾具和帶有可移動元件的夾具配套件），或者裝有陶瓷或硬化了的中介物質（如：流動粒子床夾具和熱夾具緊夾具）。為了生產，零件要在夾具中被緊固，需要產生夾緊作用，其有幾個與夾具柔順性無關的步驟：
根據被加工的即基礎的部分和工作特點，確定工件在夾具中的所需的位置，接著必須選擇若干穩定平面的組合，這些穩定平面就構成工件被固定在夾具中確定位置上的夾持狀輪廓結構，均衡所有各力和力矩，而且保證接近工件工作特點。最后，必須計算、調整、組裝可拆裝的或標準夾具元件的所需位置，以便使工件牢牢地被夾緊在夾具中。依據這樣的程序，夾具的輪廓結構和裝合的規劃和記錄過程可以進行自動化控制。
結構造型任務就是要產生若干穩定平面的組合，這樣在這些平面上的各夾緊力將使工件和夾具穩定。按慣例，這個任務可用人—機對話即幾乎完全自動化的方式來完成。一人—機對話即以自動化方式確定夾具結構造型的優點是可以有組織有規劃進行夾具設計，減少所需的設計人員，縮短研究周期和能更好地配置工作條件。簡言之，可成功地達到顯著提高夾具生產效率和效益。在充分準備了構造方案和一批材料情況下，在完成首次組裝可以成功實現節約時間達60%。
因此夾具機構造型過程的目的是產生合適的編程文件。