購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
畢 業 設 計 任 務 書
2008年3月1日
畢業設計題目
新KS型單級單吸離心泵的設計
指導教師
俞云強
職稱
講師
專業名稱
機電一體化技術
班級
機電50532
學生姓名
王 林
學號
5020053227
設計要求
在規定的時間內完成裝備圖,且產品能達到所設計的性能指標。
完成畢業課題的計劃安排
序號
內容
時間安排
1
外文資料翻譯
2008.3.1----2008.3.10
2
搜集課題相關資料
2008.3.11----2008.3.20
3
完成畢業設計說明書
2008.3.21----2008.4.1
4
預審，修改
2008.4.2----2008.4.11
5
答辯
2008.4.11----2008.4.20
答辯提交資料
外文資料翻譯，畢業設計說明書
計劃答辯時間
2008.4.20
無錫職業技術學院機電技術學院
2008年3月1日
分類號
密級
無錫職業技術學院
畢業設計說明書
題 目 新KS型單級單吸離心泵的設計
英文并列題目 New KS-absorption-type single-stage centifugal pump
學生姓名： 王 林
專 業： 機電一體化
指導教師： 俞云強
職 稱： 講 師
畢業設計說明書提交日期 2008年4月20日 地址：
無錫職業技術學院畢業設計
目錄
摘要----------------------------------------------------------------------Ⅱ
Abstract------------------------------------------------------------------Ⅲ
新KS型單級單吸離心泵的設計------------------------------------------------------------------------1
第1章 引言--------------------------------------------------------------1
第2章 型號意義示例------------------------------------------------------2
第3章 新KS型單級單吸離心泵的主要性能參數-------------------------------3
第4章 新KS型單級單吸離心泵的特性曲線-----------------------------------5
第5章 新KS型單級單吸離心泵工作原理-------------------------------------6
第6章 新KS型單級單吸離心泵的主要部件-----------------------------------7
6.1 葉輪----------------------------------------------------------7
6.2 泵殼----------------------------------------------------------7
6.3 泵軸----------------------------------------------------------10
6.4 軸承----------------------------------------------------------11
6.5 懸架----------------------------------------------------------11
6.6 機械密封------------------------------------------------------13
6.7 填料函--------------------------------------------------------14
第7章 新KS型單級單吸離心泵的安裝---------------------------------------15
第8章 新KS型單級單吸離心泵的水泵檢驗標準-------------------------------17
第9章 新KS型單級單吸離心泵的操作程序-----------------------------------21
第10章 合理配置、安全運行、優質供水-------------------------------------24
第11章 新KS型單級單吸離心泵容易發生的故障------------------------------26
第12章 新KS型單級單吸離心泵間性能的改變和換算--------------------------29
第13章 離心泵流量控制方法探討-------------------------------------------30
第14章 結束語-----------------------------------------------------------31
致謝-----------------------------------------------------------------------31
參考文獻-------------------------------------------------------------------32
畢業設計小結---------------------------------------------------------------33
摘 要
KS型單級單吸離心泵吸收了KT、SB、ES、IS、XA及國外優秀離心泵系列產品的優點，采用了多項水力設計及工藝方法的發明專利和實用新型專利而研制開發的高新技術系列產品。它廣泛用于空調、制冷、冰蓄冷、自來水廠、消防、環保、高層供水和城鄉排水等領域，一般輸送85攝氏度以下清水或物理化學性質類似清水的液體。通過變換泵的結構及材質可輸送高溫及腐蝕性介質，可用與化工、冶金等行業。本系列產品產品具有高效率、高性能、高耐壓、高可靠性和安裝維修方便等特點，其結構參數符合國際標準產品相互替代，承壓能力為1.6MPa級，諸項技術經濟指標達到國外同類產品先進水平，屬于國際接軌的換代產品。
注：單級單吸離心泵為一個葉輪一個進水口的離心泵。
關鍵詞：單級單吸、葉輪、機械密封、安裝、故障分析。
Abstract
KS-absorption-type single-stage centrifugal pump absorption of KT, SB, ES, IS, XA and abroad outstanding merits of the centrifugal pump series with a number of hydraulic design and technology of the invention patent, and a patent application of a new and high-tech research and development technology products. It is widely used in air conditioning, refrigeration, ice storage, the water plant, fire protection, environmental protection, urban and rural water supply and drainage senior in areas such as transport 85 degrees Celsius below normal water or similar physical and chemical properties of liquid water. Transform pump through the structure and materials can be corrosive and high temperature transmission medium can be used with the chemical, and metallurgical industries. Products in this series of high efficiency, high performance, high pressure, high reliability, and easy installation and maintenance characteristics of the structural parameters in line with international standard products as an alternative, the pressure of 1.6 MPa-capacity, all of the technical and economic indicators have reached abroad Similar Products advanced level of international standards generations.
Note: single-stage centrifugal pump for a single suction inlet of an impeller centrifugal pump.
Key words: single-stage-to smoke, impeller, mechanical seals, installation, fault analysis.
III
外文翻譯資料
Last scanner control system development
鞋楦掃描機的控制系統的開發
1 Introduction
In the global footwear industry, which has been China's footwear industry is. A short period of 10 years, China has risen remarkably, to the world's largest footwear producer and exporter. The rapid development of the footwear industry was driven by the shoe last industry, more and more shoe styles, and also requires constant renovation shoe last, which led to the shoe last from durable goods become consumables. Mechanical shoe last copying machine is used for processing principle, it implements the shoe last of the production process, bringing the shoe last, the rapid development of industry. But mechanical shoe last machine also has its inevitable drawbacks: First, from the product perspective, it processed by the upper sides of the shoe last, the more obvious Weijidao longitudinal marks, shoe last very smooth, as this request increasing the shoe-making industry, it is unable to meet the requirements of Secondly, mechanical machines in the shoe last of shoe last zoom, manual adjustment of the workforce to use their experience machines, which require workers relatively high; again, and most important, the traditional processing methods unable to establish workpiece size of the document, they can not do anything to modify the shape.
1 引言
在全球制鞋業中，中國制鞋業可謂異軍突起。短短的十多年，中國一躍升為全球最大的鞋類生產國和出口國。制鞋業的迅猛發展也帶動了鞋楦業，鞋子的樣式越來越多，就要求鞋楦也要不斷翻新，這促成了鞋楦從耐用品變成易耗品。機械鞋楦機采用的是仿形加工的原理，它實現了鞋楦加工的批量生產，帶來了鞋楦業的飛速發展。但是機械鞋楦機也有其不可避免的缺點：首先，從產品角度來講，它加工出來的鞋楦的鞋幫兩側，總有幾道較明顯的縱痕，鞋楦很不光滑，這對于要求越來越高的制鞋業來說，是不能滿足要求的；其次，機械鞋楦機在實現鞋楦的縮放時，需要工人憑經驗手工調整機器，這對工人要求比較高；再次，也是最重要的，傳統的加工方法無法建立工件尺寸的文件，也無法做任何的外形修改。
2 NC-shoe last two figures of reverse engineering system
Last CNC machine can be avoided mechanical shoe last machine shortcomings. CNC machine using digital shoe last of the reverse engineering system, the digital system in the reverse engineering of the shoe last model 3D scanning, are three-dimensional model of data files, by addressing data file (such as dealing with a smooth surface, interpolation processing, etc.) Implementation of the shoe last scalable model, and change the shoe last machined surface of the helix pitch, thereby improving the quality of surface machining. At the same time, the data files can be stored in computer may need to tune out the same type of shoe last only one scan, management is very convenient. Clearly, the number of such reverse engineering system to meet modern shoe last is the development of the industry. NC-figure shoe last reverse engineering flowchart in Figure 1 below:
Zoom appearance code revision
Last Model
3D Scanning
Data Processing
Computer-assisted analysis
Construction of 3D model
Computer aided manufacturing
Rapid Tooling
Last products
Figure 1 NC shoe last for the number of reverse engineering flowchart
???? Last abroad NC machine has been very well so far, in the practical application has been greatly affirmed. Our domestic Due to various reasons, a late start, the author of the reference laboratory in foreign machinery under the premise of the practical application as the main purpose of NC Machine for shoe last for domestic enterprises in the area to provide some reference. Last of the NC machines composed of two parts, part scanner, be it by scanning the shoe last three-dimensional data, and the other part is carved Last machine, which uses a three-dimensional scan data processing by the shoe last. This paper mainly discusses the shoe last scan machine control system design, only by scanning the data files accurately, to ensure processing by the quality of the shoe last, shoe last scan machine of shoe last is the basis and premise for processing.
2 數控鞋楦機的數字化逆向工程系統
數控鞋楦機可以避免機械鞋楦機的缺點。數控鞋楦機采用數字化的逆向工程系統，數字化的逆向工程系統在對鞋楦模型進行三維掃描后，得到模型的三維數據文件，通過處理數據文件（如表面光滑處理，插值處理等），實現對鞋楦模型的縮放，并能改變鞋楦加工表面的螺旋線的螺距，從而改善加工表面的質量。同時，所得數據文件可以存入電腦，需要時可再調出來，同一類型的鞋楦只需掃描一次，管理非常方便。顯然，這樣的數字化逆向工程系統才是滿足現代鞋楦業的發展的。數控鞋楦機的數字逆向工程流程圖如圖1所示：
??? 圖1 數控鞋楦機的數字逆向工程流程圖
國外的數控鞋楦機到目前為止已經非常完善了，在實際應用中也得到極大肯定。我們國內由于種種原因，起步較晚，所以筆者所在實驗室在參考國外機器的前提下，以實際應用作為主要目的，進行數控鞋楦機的研制，為國內在該領域的企業提供一些參考。該數控鞋楦機有兩部分組成，一部分是掃描機，它通過掃描得到鞋楦的三維數據，另一部分是刻楦機，它利用掃描得到的三維數據加工出鞋楦。本文主要討論鞋楦掃描機的控制系統設計，只有掃描得到的數據文件準確，才能保證加工出來的鞋楦的質量，因此鞋楦掃描機是實現鞋楦加工的基礎和前提。
3 shoe last scanners scan Principle
First, a brief introduction to the shoe last scanner scanning principle, as shown in Figure 2.
?
???? Figure 2 shoe last scanners scan schematic
???? As shown below, driven shoe last X-axis of rotation, Y-axis is at the center shoe last, in the Z-axis length shoe last move, that is, the direction of mobile scanning round. Last scanner using contact measurement, measurement tools used for scanning round, it installed in the Y-axis direction, scanning round rely on the shoe last, behind by the pump withstand, scanning round of the campaign with the shoes before and after moving, behind the wheel grating scanning device data acquisition shoe last.
3 鞋楦掃描機的掃描原理
首先，簡要介紹一下鞋楦掃描機的掃描原理，如下圖2所示。
??? 圖2 鞋楦掃描機的掃描原理圖
如上圖所示，X軸帶動鞋楦的自轉，Y軸為指向鞋楦中心線，Z軸在鞋楦長度方向移動，即掃描輪移動的方向。鞋楦掃描機采用接觸式測量方式，所用測量工具為掃描輪，它安裝在Y軸方向，掃描輪靠在鞋楦上，其后面由氣泵頂著，掃描輪隨著鞋子的運動而前后移動，掃描輪后面的光柵尺采集鞋楦數據。
4 shoe last scan machine control system outlined
?? Last scanner using PC as a PC, using the object-oriented language VC + + software design, development, through the Motion Control Card drive system and three-axis collection of data by scanning data files, for use in processing. PC operating as a scanner interface, complete data analysis, processing and the implementation of the control, and other tasks. Motion Control Card as a control center, sending and receiving complete pulse. Accept board sent servo motor pulse, drive shaft various campaigns At the same time, servo motor encoder feedback to the motion control. Diagram of the control system are shown in Figure 3.
No. 0-axis encoder feedback signals
Optical grating feedback system
DMC3000
No.2-axis encoder feedback signals
No. O-axis and the direction of the output pulse
Section 0.1 axis origin and spacing signal
No. 1-axis and the direction of the output pulse
Various axis limit switch
C-axis servo system
Z-axis servo system
No. 1-axis encoder feedback signals
Figure 3 diagram of the control system
???? Below are introduced Motion Control Card, servo motor and optical grating choice and control.
4 鞋楦掃描機的控制系統概述
鞋楦掃描機采用PC機作為上位機，利用面向?qū)ο蟮恼Z言VC＋＋進行軟件設計、開發，通過運動控制卡驅動系統并采集三根軸的數據，得到掃描數據文件，以用于加工。上位機作為掃描機的操作界面，完成數據分析、處理以及對執行機構的控制等任務。運動控制卡作為控制核心，完成發送及接收脈沖。伺服電機接受板卡發送的脈沖，驅動各個軸運動，同時，伺服電機編碼器反饋給運動控制。整個控制系統簡圖如下圖3所示。
??? 圖3 控制系統總框圖
下面主要介紹運動控制卡，伺服電機以及光柵尺的選擇及控制。
4.1 Motion Control Card choice and control
?? In the scanning system, the Motion Control Card is the core of the whole system, choose a suitable motion control card is very important.
?? In the scanning process, the motion control card and the need to control the X-axis Z-axis servo motors, motion control card not only to send pulses to the motor drives, servo motor at the same time accept encoder feedback pulses. Motion Control Card also accepted optical grating feedback signal. Because it is collecting shoe last three-dimensional data, the more intensive sampling and processing the products more smooth. In this system, setting shoe last lap to the needs of hundreds of point sampling, the Motion Control Card Driver output pulse requirement is relatively high, the encoder input frequency of a certain request, a few requirements triaxial control axis. A mix of different properties, as well as economic, as well as their choice of Shenzhen Company, the mine DMC3000 series Motion Control Card.
?? Motion Control of the system is based on the PCI bus card, high-performance motion control card can control up to 4-axis stepper or servo motor. This series of plug-and-play with a maximum pulse frequency of 4 MHz, the S-curve damping function, encoder feedback, and advanced features such as variable speed at any time.
?? Motion Control Card of the axis of each of the two signal outputs can be used to PUL and DIR output pulse and direction signal, which can be output from the two procedures are set to pulse-pulse + (double-pulse) + pulse mode or direction mode ( single pulse). The system uses pulse + direction form, and set the pulse for the differential output, in the differential output mode, a signal can be divided into a different bad signal. The use of differential output can be an effective way to reduce transmission interference, and improve reliability. X-axis and the Z-axis servo motor drive from the Motion Control Card to receive the signal pulse and direction.
The Motion Control Card may simultaneously control four-axis, the axis of each have three pairs of differential phase A, B and Z of the input signal, EA and EB signal used for position, the signal for the origin EZ index signal. Each axis has a switching signal origin through the mechanical origin of the signal input shaft to find the original point of origin can be set through the software switch-mode. Each axis has two locations spacing signal EL + (positive spacing) and EL-(reverse Limit), the limit set by switch-mode software. In this system, the X-axis and the Z-axis servo motor feedback encoder pulse signal have access Motion Control Card. Since the initial movement of each axis there is a start bit, it was necessary to signal to the original point, the search software to determine the origin signal the start bit. X axis rotation direction, do not limit pros and cons, using only a signal origin. Apart from the Z-axis origin signal, but also limit access plus or minus two position signals from the two limit protection. I universal digital input and output can also be used to access some of the switch signal.
The single campaign, according to campaign-distance, the motion control card, the mode of operation and continuous operation mode. According to the velocity, the trapezoidal motion control card that runs at S-curve pattern and operation mode. S-curve model used to run a shaft that runs at the S-curve designated pulse number of S-curve model can be run effectively and to improve acceleration and deceleration eliminate the vibration, so that movement is very smooth. Figure 4 shows the following:
?
???? Figure 4 S-curve velocity and acceleration
?? Since S curve in a trapezoidal mode runs at the merits of this system are used in the operation mode S-curve. Before the start of the scan, in order to measure the floor straight shoe last longer need to shoe last turn certain angle, and then use fixed-length operation mode. In the scanning process, the Z-axis and the X-axis but at the same time the implementation of an independent movement, and movement is continuous. This two-axis at the same time guarantee a certain percentage of the speed sports. Actual circumstances, the Motion Control Card of the system can meet the requirements of shoe last of the three-dimensional data scanning, and thus gained three-dimensional data files shoe last.
4．1 運動控制卡的選擇及控制
? 在掃描系統中，運動控制卡是整個系統的核心，因此選擇合適的運動控制卡是很重要的。
??? 在掃描過程中，運動控制卡需要控制Z軸和X軸的伺服電機，運動控制卡不僅要發送脈沖給電機驅動器，同時接受伺服電機編碼器反饋的脈沖數。運動控制卡還接受光柵尺反饋信號。由于是采集鞋楦三維的數據，采樣點越密集，加工出來的產品越光滑。在本系統中，設定鞋楦轉一圈需要采樣幾百個點，因此對運動控制卡的驅動輸出脈沖要求比較高，對編碼器輸入頻率也有一定要求，控制軸數要求三軸。綜合考慮各種性能以及經濟性等,選擇深圳雷賽公司的DMC3000系列運動控制卡。
??? 本系統的運動控制卡是基于PCI總線的高性能運動控制卡，可控制多達四軸步進或伺服電機。此系列具有即插即用、最高4MHz脈沖頻率、S曲線減振功能、編碼器反饋、隨時變速等高級功能。
??? 本運動控制卡的每一軸的兩個信號輸出口PUL和DIR可用來輸出脈沖和方向信號，這兩個輸出口可以由程序設成正脈沖+反脈沖（雙脈沖）模式或脈沖+方向模式（單脈沖）。本系統采用脈沖+方向形式，并設定脈沖為差分輸出方式，在差分輸出模式下，每一個信號可以被差分成一對相異的信號。使用差分輸出方式可有效的減少傳輸中的干擾，提高可靠性。X軸和Z軸的伺服電機驅動器接收來自運動控制卡的脈沖和方向信號。
?? 本運動控制卡可同時控制四根軸，每一軸都有三對差分的A相、B相和Z相輸入信號，EA和EB信號用來進行位置計算，EZ信號用作原點索引信號。每一軸都有一個原點開關信號，通過機械原點信號輸入來查找該軸的原點，可通過軟件設定原點開關模式。每一軸都有兩個位置限位信號EL+（正向限位）和EL-（反向限位），可通過軟件設定限位開關模式。在本系統中，X軸和Z軸的伺服電機編碼器反饋的脈沖信號都接入運動控制卡。由于每根軸運動初始有個起始位，因此需要用原點信號，軟件通過搜索原點信號來確定起始位。X軸為旋轉方向，不需要正反限位，只采用一個原點信號。Z軸除了原點信號外，還接入正負兩個位置限位信號，兩個限位起保護作用。通用數字輸入輸出口也可用來接一些開關信號。
對于單軸運動，按照運動距離來分,本運動控制卡有定長運行模式和連續運行模式。按照運動速度來分，本運動控制卡有梯形速度運行模式和S曲線運行模式。S曲線運行模式用來讓一根軸以S曲線速度運行指定脈沖數，S曲線運行模式可以有效消除并改善加減速時的振動，使運動非常平滑。如下圖4所示:
??? 圖4 S曲線速度及加速度
由于S曲線運行模式較于梯形速度運行模式的優點，本系統中均采用S曲線運行模式。在掃描開始前，為了測量鞋楦的底板直長，需要將鞋楦轉過一定角度，這時采用定長運行模式。在掃描過程中，Z軸和X軸執行同時但獨立的運動，并且是連續運動。同時保證這兩根軸以一定的比例速度運動。實際情況證明，本運動控制卡能滿足本系統的要求，實現鞋楦數據的三維掃描，從而得到鞋楦三維據文件。
4.2 servo motor control and choice
Since the control system for the real-time requirement is relatively high, motion control card sent to the motor drive pulses to the pulse motor immediately, not delayed, not wrong. Thus the control system could not be used stepper motor and servo motor systems must be used. At the same time servo motor control with high accuracy, strong Guozainaili, speed response performance, and reliable operation of a series of advantages. In this system, we have selected Panasonic Digital MSDA0231A1A AC servo drives, servo motor configuration for MSM022A1. Bring the drive motor rated output power of 1.5 kw, incremental rotary encoder for the P-2500 / r, 3-phase input power for 220 V, rated speed of 2000 r / m.
Request to place the system more accurate rapidly, as in the shoe last lap to (X-axis rotation lap) needs hundreds of sampling point, the response of the servo system requirements relatively high. At the same time, the servo motor parameters on the quality of scanning has a certain impact. Used in the control system mode, the servo motor will be adjusted to the parameters of a better situation, mainly the following parameters.
??1. NO.10 parameters (location of the first loop gain) definition of the position control response curve, the higher gain settings, the faster positioning time.
???2. NO.11 parameters (first speed loop gain) and the parameters NO.10 servo system with access to the total response curve. As far as possible, high-gain settings.
???3. NO.15 parameters (speed feed-forward) to set the pace in the position control of feedforward. In the constant speed motor running, if this value as a 100% position deviation almost zero. This value is set higher, so to a lesser position error was faster response, but it may lead to overshoot.
??By NO.46, NO.4B parameter settings can be very convenient with a variety of command pulse frequency matched to achieve the desired control resolution (angle / pulse). The value of the difference between the two caused the decline in control accuracy. It is recommended settings NO.46/NO.4B (ie: electronic gear ratio): 1 / 50
收藏