喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有，，圖紙均為高清圖，，CAD圖紙可自行編輯，，有疑問咨詢QQ:1064457796
彎板沖壓成型工藝與模具設計
摘要本設計題目為彎板沖壓成型工藝與模具設計，體現了一般中等復雜性零件的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了自己沖壓模具設計的基礎知識，為設計更復雜的模具做好了鋪墊和吸取了更深刻的經驗。
本設計運用沖壓成型工藝及模具設計的基礎知識，首先分析了沖壓的成型工藝，為工藝方案的選取類型做好了準備；然后計算了沖壓件的展開尺寸，查取所用材料料厚的沖裁間隙及成型工藝參數，便于刃口尺寸計算。
本沖壓件的形狀大致為帶孔平板尾部折U型彎，所以在排工藝時考慮成型工序與沖孔工序的先后。先沖孔后成型，由于成型時產生拉力會造成孔位置偏移；先成型后沖孔會造成模具復雜程度增加進而增加模具制造成本。根據產品圖所示相關公差要求結合實際生產中彎板的使用過程，分析空位置稍有偏差對產品的質量影響，如孔位置對對產品質量影響較大時，只能考慮先成型后沖孔工藝，反之則采用先沖孔后成型以降低模具制造成本和生產周期。
對工藝方案擬定以后，查詢相關設計手冊和資料并在指導老師的悉心指導下對模具總裝及相關零部件進行逐一設計校核。
最后檢查所有設計步驟，進行系統地查漏補缺，完善模具設計。
關鍵詞：彎板 沖裁 成型 工序
Bending plate stamping forming process and die design
Abstract
This design topic for stamping process and die design of bending plate, reflects the design of moderate complexity parts requirements, content and direction, the design of a certain significance. Through the design of the die parts, to further strengthen their basic knowledge of stamping die design, paving the way and draw a more profound experience for die design more complex.
This design using the basic knowledge of stamping forming process and die design, firstly analyzed the molding process of stamping, ready for the selected type of process scheme; expand size stamping calculates, check the material blanking clearance and molding process parameters calculation of thick, easy cutting edge size.
The stamping shape roughly flat plate with a hole tail fold type U bent, so in the discharge process when considering successively forming and punching process. The first punch forming, the forming force will cause the hole position offset; the first forming die punching will result in increasing the complexity and increase the mold manufacturing costs. According to the products shown relative tolerance requires the use of plate bending process combined with the actual production, analysis of space position a little deviation on the quality of products, such as hole position on the effect on the quality of large, can only consider the first forming punching process, whereas the punching forming to reduce the manufacturing cost and production cycle.
The process scheme, query design manual and data and by design to mold assembly and related parts and components under the guidance of the instructor.
Finally, check all design steps, the systematic gaps, improve the mold design.
Keywords: bending plate blanking molding process
II