購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載就能得到。。?！咀ⅰ浚篸wg后綴為CAD圖，doc,docx為WORD文檔，【有不明白之處，可咨詢QQ:1304139763】
摘 要 本文介紹的模具實例結構簡單實用 使用方便可靠 本套沖壓模具的設計不是以復雜 模具的設計為主 而主要是對模具設計知識的系統學習和設計的練習 以達到掌握沖壓模 具設計的基本技能的目的 首先 對零件做整體的分析 包括 材料的使用 精度的要求 工序的要求以及成本 的要求等 為了降低成本 對排樣方式進行了合理的設計 其次 對零件整體進行工藝設 計 通過工藝目的的設計 工序的順序設計 壓力機的選擇等來實現所要達到的要求 再 次 想要保證制件精度的要求 就要考慮模具刃口尺寸的計算 因?yàn)槿锌谑菦_制工件的主 要工作部分 刃口處的精度就決定了制件的精度 就必須根據公差來進行精確計算 最后 根據計算出的模具刃口尺寸設計出相應的凸凹模 并且查找資料選擇冷沖壓模 的標準零件 符合標準后 就把凸凹模與其它各零部件進行總體裝配 在確定了模具體閉 合高度后 選出合適的壓力機在調試校驗后并進行試沖加工 以達到符合的標準 最終完 成加工 關鍵詞 沖壓模具 沖壓工藝 模具設計 Abstract The topic is the chain plate punching blanking compound mold design and the mold of article described an instance is simple and practical easy to use and is reliable This mold is not primarily designed to complex design but mainly on a systematic study of mold design knowledge and practice in order to achieve the purpose of master the basic skills of stamping mold design First of all do a thorough analysis for the parts which include the using of the material the requirement of accuracy and the requirement of working procedure and costs and so on For declining low cost proceeded the reasonable design to the row kind method Secondly do processing design for the whole parts and the purpose by craft designing and order of the working procedure and by the choice of punching machine Thirdly consider the calculation of size of the mould cutting edge in order to meet the need of accuracy Because the cutting edge is the main working part of the punching processing the accurate cutting edge guarantees the accurate parts So you needed to tolerance do accurate calculation Finally according to the calculated the size of mold cutting edge design the corresponding punch and mold and find information on selection criteria for cold stamping parts meet the standards put the punch and mold with the other components to the overall assembly In determining the specific mold closed height select the appropriate press in the debug and test validation washed after processing to meet compliance standards the final completion of the processing chain plate Keywords composite modulus stamping process mold design punching blanking 目 錄 摘要 1 Abstract 2 目錄 3 第 1 章 緒論 5 1 1 我國模具技術的現狀及發展趨勢 5 1 2 沖壓模的現狀與發展趨勢 6 1 3 外國模具工業的發展?fàn)顩r 7 1 4 課題研究的內容 8 第 2 章 工藝性分析 9 2 1 零件的分析 9 2 1 1 沖壓件的尺寸精度 9 2 1 2 生產批量 9 2 2 工藝方案分析 10 2 3 模具間隙的確定 11 2 4 設備的選擇 12 第 3 章 排樣設計 15 3 1 搭邊 17 3 2 送料進距 17 3 3 條料寬度 17 3 4 本章小結 18 第 4 章 模具總體設計 19 4 1 模具類型的選擇 19 4 2 定位方式的選擇 19 4 3 卸料 出件方式的選擇 20 第 5 章 模具的裝配和沖裁模具的試沖 21 5 1 模具的裝配 21 5 2 沖裁模具的試沖 22 5 3 裝配圖 25 結論與展望 26 致謝 27 參考文獻 28