《復合片外圓磨削用陶瓷結合劑金剛石砂輪的研制及應用》由會員分享，可在線閱讀，更多相關《復合片外圓磨削用陶瓷結合劑金剛石砂輪的研制及應用（1頁珍藏版）》請在裝配圖網上搜索。
1、第23卷第1期
2011年2月
Vol. 23
Feb. 2011
起減材 44 X «
SUPERHARD MATERIAL ENGINEERING
復合片外圓磨削用陶瓷結合劑
金剛石砂輪的研制及應用
劉一波，劉偉，黃霞,楊德濤
(北京安秦鋼研超硬材料制品有限責任公司，北京畐半102200)
播 要：研究了復合片外圖房刑用陶近結合刑金明石砂輪的制備工藝只其應用■確定了合適的工藝歩數. 結果表明*自制Li-Al-B-Si-0系低溫陶近結合劑含童在22%?26%時，矽輪的綜合，14能達到最伐： 砂輪中舟料濃度越高，使用效果越好，隨矽輪中房軒濃度的增加?砂輪的性價
2、比遂漸提離，當濃度達列 210%時?矽輪的壽令達到瓷砂輪比樹脂砂輪的壽令提高2?3倍，且單件復合片的庭利效率提高 約30%$所研甸的低溫陶先金剛石砂輪妹合柱能達到國內領先水平具有較高的性價比.
關St詞：JL合片»外圓磨frh陶近結合刑)金剛石砂輪 中圖分類號:TQ164 文獻標識碼：A 文章編號：1673 —1433(2011 )01 — 0001-04
Investigation and application on vitrified bond diamond grinding wheels
for cylindrical grinding polycrystalline
3、 diamond compacts
LIU Yi-bof LIU Wei, HUANG Xia, YANG De^tao
(Beijing Gang Yan Diamond Products Company 9 China Iron & Steel Research Institute Group 9 Beijing 102200, China)
Abstract：The preparation and application of vitrified bond diamond grinding wheel for PCD cylindrical grinding use hav
4、e been investigated and proper technique parameters have been developed? The results show that： grinding wheels give the best comprehensive performances when the self-made Li-Al-B-Si-0 series vitrified bond content is about 22% ? 26%; diamond concentration brings good effect on its application until
5、 the concentration up to 210%f the wheel reaches the longest life; working life of vitrified bond grinding wheel are much longerf about 2?3 times more than resin wheel and efficiency of grinding a single PDC can be improved about 30% compared to resin wheel; comprehensive performance of the develope
6、d low temperature vitrified bond grinding wheels reaches the leading level and is much competitive.
Keywords: PDCf cylindrical grinding, vitrified bond, diamond grinding wheel
0前言
的金剛石微粉層與硬質合金基體在高壓高溫(5
1
第23卷第1期
2011年2月
Vol. 23
Feb. 2011
7GPa J400C?1700D條件下復合而成的超硬復
聚晶金剛石復合片(PDC)是指0.1至數毫米厚 合材料，它具有高硬度、高耐磨性.高彈性模量.各項
收橋日期：2011—03 —15
作者簡介：劉…波(1966-),安泰鋼研超便材料公司總T.稷師兼副總經理?Email Jiuyibo^atmcn. com
1
復合片外圓磨削用陶瓷結合劑金剛石砂輪的研制及應用
