喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:414951605 或 1304139763】
========================================喜歡這套資料就充值下載吧。。。資源目錄里展示的都可在線預覽哦。。。下載后都有，，請放心下載，，文件全都包含在內，，【有疑問咨詢QQ:414951605 或 1304139763】
========================================
附 錄1
什么是液壓？
一個完整的液壓系統由五個部分組成，即動力元件、執行元件、控制元件、無件和液壓油。動力元件的作用是將原動機的機械能轉換成液壓體的壓力能，指液壓系統中的油泵，它向整個液壓系統提供動力。液壓泵的結構形式一般有齒輪泵、葉片泵和柱塞泵。執行元件（如液壓缸和液壓馬達）的作用是將液體的壓力能轉換為機械能，驅動負載作直線往復運動或回轉運動?？刂圃锤鞣N液壓閥）在液壓系統中控制和調節液體的壓力、流量和方向。根據控制功能不同，液壓閥可分為壓力控制閥、流量控制閥和方向控制閥。壓力控制閥又分為溢流閥、減壓閥、順序閥、壓力繼電器等；流量控制閥包括節流閥、調整法、分流集流閥等；方向控制閥包括單向閥、液控單向閥、換向閥等。根據控制方式不同，液壓閥可分為開關式控制閥、定值控制閥和比例控制閥。輔助元件包括油箱、濾油器、油管及管接頭、密封圈、壓力表、液位液溫計等。液壓油是系統中傳遞能量的工作介質，有各種礦物油、乳化液和合成型液壓油等幾大類。
液壓的原理,它是由兩個大小不同的液壓缸組成的，在液壓缸里充滿水或油。充水的叫“水壓機”；充油的叫做“油壓機”。兩個液壓缸里各有一個可以滑動的活塞，如果在小活塞上加一定值的壓力，根據帕斯卡定律，小活塞將這一壓力通過液體的壓強傳遞給大活塞，將大活塞頂上去。設小活塞的橫截面積是S1，加在小活塞上的向下的壓力是F1。于是，小活塞對液體的壓強為P=F1/S1，能夠大小不變地被液體向各個方向傳遞。大洪塞所受到的壓強必然也等于P。若大活塞的橫截面積是S2，壓強P在大活塞上所產生的向上的壓力F2=PxS2截面積是小活塞橫截面積的倍數。從上式知，在小活塞上加一較小的力，則在大活塞上會得到很大的力，為此用液壓機來壓制膠合板、榨油、提取重物、鍛壓鋼材等。
液壓傳動的發展史,液壓傳動和氣壓傳動成為流體傳動，是根據17世紀帕斯卡提出的液體靜壓力傳動原理而發展起來的一門新興技術，1795年因果約瑟夫·布拉曼，在倫敦用水作為工作介質，以水壓機的形式將其應用于工業上，誕生了世界上第一臺水壓機。1905年將工作介質水改為油，又進一步得到改善。第一次世界大戰后液壓傳動廣泛應用，特別是1920年以后，發展更為迅速。液壓元件大約在19世紀末20世紀初的20年間，才開始進入正規的工業生產階段。1925年維克斯發明了壓力平衡式葉片泵，為近代液壓元件工業或液壓傳動的逐步建立奠定了基礎。20世紀初康斯坦丁·尼斯克對能量波動傳遞所進行的理論及實際研究；1910年對液力傳動方面的貢獻，使這兩方面領域得到了發展。
第二次世界大戰期間，在美國機床中有30%應用了液壓傳動。應該指出，日本液壓傳動的發展較歐美等國家晚了近20多年。在1955年前后，日本迅速發展液壓傳動，1956年成立了“液壓工業會”。近20~30年間，日本液壓傳動發展之快，居世界領先地位。
液壓傳動有許多突出的優點，因此它的應用非常廣泛，如一般工業用的塑料加工機械、壓力機械、機床等；行走機械中的工程機械、建筑機械、農業機械、汽車等；鋼鐵工業用的冶金機械、提升裝置、軋輥調整裝置等；土木水利工程用的防洪閘門及堤壩裝置、河床升降裝置、橋梁操縱機構等；發電廠渦輪機調速裝置、核發電廠等等；船舶用的甲板起重機械（絞車）、船頭門、艙壁閥、船尾推進器等；特殊技術用的巨型天線控制裝置、測量浮標、升降旋轉舞臺等；軍事工業用的火炮操縱裝置、船舶減搖裝置、飛行器仿真、飛機起落架的收放裝置和方向舵控制裝置等。
液壓技術作為實現現代傳動與控制的關鍵基礎技術之一，已成為工業機械、工程建設機械及國際尖端產品不可缺少的重要技術基礎。是它們向自動化、高精度、高效率、高速度、小型化、輕量化方向發展的關鍵技術。世界工業發達國家都將液壓工業列為競爭發展的行業，其發展速度遠高于機械工業的發展速度。液壓元件及其控制已發展成為綜合的液壓工程技術。
機械制造是為國民經濟各部門和自身技術改造提供先進技術裝備的工業部門。鑄造、鍛壓、焊接、熱處理、及切削等是機械制造工業獲取毛坯、成形產品及提高零件機械性能的重要生產方法，在眾多金屬冷、熱加工機器設備中普遍使用液壓技術，其中壓力機和金屬切削機床是應用液壓技術較早較廣的領域。
在車、銑、刨、磨、鉆各類液壓機床中，主要利用液壓技術可在較寬范圍內進行無級調速，具有良好的換向及換接性能，易于實現工作循環等優點，完成工件及刀具的夾緊、控制進給速度和驅動主軸作業，盡管現代數控機床、加工中心等先進制造設備中采用電伺服系統，但采用液壓傳動與控制仍然是現代金屬切削機床自動化的重要途徑。在鍛造機、液壓機、折彎?rùn)C(jī)、剪切機等壓力加工設備中，主要利用液壓傳動傳遞力較大、便于壓力調節控制和過載保護的特點，進行下料、成形加工等作業。鑄造、鍛壓、焊接、熱處理等機器設備的生產作業環境極為惡劣，溫度高、粉塵多、濕度大、有腐蝕性氣體、振動噪聲大。因此要求機器要有良好的適應性、可靠性和維護性。在造型機及澆鑄機、焊接機、淬火機等鑄造、焊接及熱處理機器設備中，主要利用液壓技術便于無級調速和遠距離遙控作業等特點，進行造型及鑄型輸送與澆鑄、高溫零件抓取等作業，以減輕勞動者勞動強度、避免和減少熱輻射和有害氣體對人身的侵襲并提高生產率。
液壓傳動有許多突出的優點，因此它的應用廣泛，如一般工業用的塑料加工機械、壓力機械、機床等；行走機械中的工程機械、建筑機械、農業機械、汽車等；鋼鐵工業用的冶金機械、提升裝置等；土木水利工程用的防洪閘門及堤壩裝置、河床升降裝置、橋梁操縱機構等；發電廠渦輪機調速裝置、核發電廠等等；船舶用的甲板起重機械、船頭門等；特殊技術用的巨型天線控制裝置、測量浮標、升降旋轉舞臺等；軍事工業用的火炮操縱裝置、船舶減搖裝置、飛行器仿真、飛機起落架的收放裝置和方向舵控制裝置等。
各種規格的鋼絲繩廣泛應用于工業領域。無論吊裝，運輸，遠洋船舶，礦山和威爾斯，港口和碼頭或各種起重機械，大量的鋼絲繩是必要的。
隨著工業的不斷發展，使用和消耗量不斷增加。然而，鋼絲繩應在一定的長度和安裝使用繩索護套。因此，鋼絲繩套壓并成為重要的機械。
鋼絲繩套機公司生產的產品具有以下特點和優勢：
1。組合式橫梁采用壓力機，具有巨大的界面模量和能承受巨大的彎曲力矩，保證新聞的強度和剛度。
2。最小的上、下橫梁的彎曲力矩，橫梁跨度的設計已最小化，優化了壓應力和壓縮結構，節約鋼材，達到科學匹配。
3。為繩套壓力機噸位大，我們采用大單位工作壓力的液壓系統中，我們認真的設計。例如，對于按1000噸以上，我們采用單位壓力55MPa，既壓縮機的結構也節省了大量的鋼材，同時，使用更方便。
4。恒功率系統是用于中、小噸位鋼絲繩套壓力機液壓系統，這不僅最大限度地減少了負載功率（由于較小的角功率）而且節省功率以實現合理用電。對鋼絲繩套壓力機噸位大，我們使用一個系統的高和低的壓力，速度快，可用于低壓和高壓合理的速度達到了。
5。對于大噸位壓機，液壓沖擊時會發生減壓由于液壓缸和高單位壓力大直徑。我們使用特殊的技術措施，為液壓系統在高壓和低壓之間的切換過程中消除液壓沖擊，因此，安全和可靠的操作就可以實現。
6。在液壓系統中大的流量，我們使用旋塞閥，液–填充閥等液壓元件以實現大流量。
7。以工人的新聞操作方便，按操作空間，前后和上下模具的安裝工作臺寬度設置很合理。
附 錄2
What is Hydraulic?
A complete hydraulic system consists of five parts, namely, power components, the implementation of components, control components, no parts and hydraulic oil. The role of dynamic components of the original motive of the mechanical energy into hydraulic body pressure energy, the hydraulic system of pumps, it is to power the entire hydraulic system. Structure of hydraulic pumps generally have the gear pump, vane pump and piston pump. Implementation of components (such as hydraulic cylinder and a hydraulic motor) is the role of the pressure of the liquid can be converted to mechanical energy to drive the load, the linear reciprocating or rotary motion. Control components (that is, the various hydraulic valves) in the hydraulic system to control and regulate the pressure of liquid, flow and direction. According to the different control functions, hydraulic valves can be divided into the pressure control valve, flow control valves and directional control valve. Pressure control valve is divided into overflow valve, relief valve, sequence valve, pressure relays; flow control valves including throttle, adjusting method, shunt valve; directional control valve includes a one-way valve, check valve, reversing valve, etc.. Under the control of different ways, hydraulic valves can be divided into the switch control valve, control valve and proportional control valve. Auxiliary components, including fuel tanks, oil filters, tubing and pipe joints, seals, pressure gauges, liquid level and temperature meter. Hydraulic oil is a medium energy transfer in the system, there are a variety of mineral oil, emulsion, hydraulic oil and other categories.
Hydraulic principle,It is composed of a hydraulic cylinder two different sizes, with water or oil in the hydraulic cylinder. Water is called "hydraulic press"; called "hydraulic machine oil". The two hydraulic cylinders, each with a piston sliding, if a certain value in the small piston on the pressure, according to Pascal's law, small piston to the pressure to the piston through the liquid pressure, the piston crown. Based cross-sectional area of the small piston is S1, plus a small piston in the downward pressure on the F1. So, a small piston on the liquid pressure is p=F1/S1, can be the same size in all directions to the transmission of liquid. Pressure Da Hong plug are also equal to P. If the cross sectional area of piston is S2, the pressure generated by the P on the piston in the pressure F2=PxS2 cross-sectional area is a small multiple of the piston cross-sectional area. From the type known, a small forces on the piston, the piston will be in great force, for which the hydraulic machine used to suppress plywood, oil extraction, weight, such as forging steel.
History of the development of hydraulic,Hydraulic and pneumatic transmission become fluid drive, is a new technology put forward according to the seventeenth Century Pascal's principle of hydrostatic pressure to drive the development of causality, 1795 Joseph Braman, in London water as working medium, to form hydraulic press used in industry, the birth of the world's first hydraulic press. Media work in 1905 will be changed to oil and water, and further improved. Widely used after the first World War, hydraulic transmission, especially after 1920, more rapid development. Hydraulic components in the late nineteenth Century and early twentieth Century about 20 years, only started to enter the formal production stage. In 1925 Vickers invented the pressure balanced vane pump, hydraulic components for the modern industrial or hydraulic transmission of the gradual establishment of the foundation. At the beginning of twentieth Century Constantine Ennis grams of fluctuation of energy transfer theory and practical research; in 1910 on the hydraulic transmission contributions, so that these two areas of development.
During the Second World War, 30% application of hydraulic drive in America machine. It should be pointed out, the national development of hydraulic transmission in Japan than Europe and the United States, nearly 20 years later. In 1955, the rapid development of Japan's hydraulic transmission, in 1956 established the "hydraulic industry". In recent years 20~30, development of Japan's fast hydraulic transmission, a leading position in the world.
There are many outstanding advantages, so it is widely used, such as general industrial use of plastic processing machinery, pressure machine, machine tool; walking machinery engineering machinery, construction machinery, agricultural machinery, automobile and so on; iron and steel industry with the metallurgical machinery, lifting device; the floodgates and dams, river bed lifting device device, bridge engineering with the manipulation mechanism; power plant turbine speed control device, a nuclear power plant and so on; with the ships deck crane, the bow door; giant antenna control device, special techniques for measuring buoy, lifting and rotating stage; military industrial gun control device, ship anti rolling device simulation of aircraft, aircraft, landing gear device and the rudder control device.
The wire ropes with various specifications are widely used in the industrial fields. Regardless of lifting, transportation, deep-sea ship, mines and wells, seaport and dock or various hoisting machinery, a large number of wire ropes are needed.
With the unceasing development of the industry, the use amount and consumption increase continuously. However, the wire ropes should be made in certain length and fitted with rope sheaths for use. So, the wire rope sheath press was introduced and became important machinery.
The wire rope sheath presses produced by our company have the following features and advantages:
1. Combination type crossbeam is adopted for the press, which has enormous interface modulus and can bear giant bending torque and ensure the strength and rigidity of the press.
2.To minimize the bending torque of the upper and lower crossbeams, the crossbeam span have been minimized in the design, which optimizes the pressing stress and compacts the structure, and saves steel material and have reached the scientific matching.
3.For rope sheath press with large tonnage, we use big unit working pressure in the hydraulic system by our conscientious design. For example, for the presses with 1000 tons and above, the unit pressure adopted by us is 55Mpa, which not only compacts the press structure but also saves large amount of steel material, meanwhile, the use is more convenient.
4.Constant power system is used for the hydraulic system of wire rope sheath press with middle and low tonnage, which not only minimizes the loading power (due to smaller angular power) but also saves power in order to realize the reasonable power using. For the wire rope sheath press with large tonnage, we use a system with both high and low pressure so that fast speed can be achieved for low pressure and reasonable speed for high pressure.
5.For press with large tonnage, hydraulic shock will occur when depressurizing due to the large diameter of the hydraulic cylinder and high unit pressure. We use special technical measures for the hydraulic system in order to get rid of the hydraulic shock in the process of switching between high and low pressure, thus safe and reliable operation can be achieved.
6.In the hydraulic system with big flow rate, we use plug valve, liquid –filled valve and other hydraulic elements in order to realize big flowing capacity.
7.In order to ensure the convenient operation of the press by the workers, the operation space of press, the width of work table from front to rear and the installation of upper and lower molds are arranged very reasonable.
8