【終稿全套】三維數控工作臺的設計與開發【4張CAD圖紙】

喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有,請放心下載，原稿可自行編輯修改=喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有,請放心下載，原稿可自行編輯修改=喜歡就充值下載吧。資源目錄里展示的全都有，下載后全都有,請放心下載，原稿可自行編輯修改= 哈爾濱理工大學學士學位論文三維數控工作臺的設計與開發摘要在當前生產中的許多機械設備中均需要精密定位，而其中的三維精密定位工作臺作為關鍵部件將直接影響其整機的性能和精度。為保證機器性能，工作臺要在X方向和Y方向?qū)崿F(xiàn)快速準確的定位，并且要求在Z方向能夠?qū)崿F(xiàn)精確調整和定位，要實現快速和準確定位，必須對工作臺進行改裝，使用步進電機和控制卡。本文設計的工作臺就是基于單片機控制的三維數控工作臺。本次研究的課題的主要內容包括：充分利用實驗室中廢舊的二維工作臺，通過對硬件諸如直線導軌，深溝球軸承，滾珠絲杠，步進電機等的選擇并對零件的整體連接結構進行設計從而組裝出一臺可運轉的三維工作臺；利用三維建模軟件對所選擇的工作臺的各部分零件進行建模，裝配，并對裝配好的三維工作臺實現運動仿真；利用VB語言對插補程序進行軟件設計；需要完成對三維工作臺的控制系統的設計，主要包括對開閉環的選擇，對80C51單片機功能的充分認識并編寫控制程序，充分理解、學習插補技術在三維數控工作臺中的應用。通過上述研究內容，我們可以的到一臺經濟，實用，精密度較高的三維數控工作臺，通過與普通工作臺的比較，我們可以從中得出插補技術對于數控工作臺的影響?？梢哉f將插補技術應用到現代數控加工已經是一個不可逆轉的趨勢，因此本課題具有很高的研究價值。關鍵詞 數控系統；三維工作臺；單片機；插補技術Design and development of 3D NC workbenchAbstractTo study the influence of the parameters of open NC servo feed systems and spatial geometry error on the precision and find methods to realize the high precision control of numerical control (NC) system, the development of the control system of a two-axis NC worktable ,consisting of ball screws and linear roller guides, was presented in this thesis. The system is based on an open architecture PMAC (Programmable multi-Axis controller) motion control card to realize real-time control. Some experiments concerning control test and error measurement and analysis can be carried out on the designed worktable. At first, the configuration of control system of the 3D NC worktable Was proposed ,and its software was developed. Modular software development concept featured the system design, which includes the following modules: machining position and speed sampled display module; file management module; parameters setting module; error diagnosis module; precision analysis module; manual debugging module; machine simulation module; help module.As one of focuses, the error measurement and precision analysis of the worktable were emphasized in the development of the system software. Series of experiments about system control and precision were made on the worktable. The precision characteristics of the half-loop and closed-loop position feedbacks were analyzed. Through comparing the theoretical analysis with the data collected from experiments ,a conclusion has been drawn that the smallest contour error will be got if the two axes have the same servo characteristics. The ball-bar ,which is considered to be more reliable than linearscales in measuring contour error, was used to measure the circular motion of the system. The experiment result showed that the contour error of the system was big .By analysis of the error source based on a mathematical model of the measuring system proposed in this thesis, it was found that it was the installation inclination of linear scales that caused so big error. By compensating the error with the measured result by the ball-bar ,the precision of the control system had been improved.Keywords Numerical Control System；three-dimensional NC workbench；SCM；Interpolation technique；III目錄摘要IAbstractII第1章 緒論11.1課題研究的意義11.2課題研究的現狀11.3課題研究的主要內容2第2章 三維數控工作臺的硬件選擇及連接結構32.1三維數控工作臺的工作原理介紹32.2三維數控工作臺的基本結構32.3步進電機的選擇42.4絲杠的選型與校核52.4.1滾珠絲杠的簡單介紹52.4.2滾珠絲杠的選型72.4.3滾珠絲杠的校核82.5直線導軌的選型與計算92.5.1直線導軌的簡單介紹92.5.2直線導軌的選型102.6聯軸器的選型122.6.1聯軸器的簡介122.6.2聯軸器的選型132.7軸承選型142.8本章小結16第3章 三維數控工作臺的Pro/E三維建模173.1 Pro/E建模軟件簡介173.2 Pro/E界面介紹173.3零件三維建模實例介紹183.3.1新建文件183.3.2建立拉伸特征193.3.3建立螺旋特征203.3.4建立螺母副特征203.3.5進行顏色和外觀設計213.4其余零件三維建模圖展示223.5三維數控工作臺裝配233.6本章小結25第4章 三維工作臺的軟件及控制系統設計264.1逐點比較法直線插補的簡介264.2逐點比較法直線插補的計算步驟264.3數控插補仿真軟件的說明294.4開環系統控制原理304.5單片機設計304.6本章小結35結論36致謝37參考文獻38附錄一39附錄二492