線圈骨架的注塑模具設計【全套設計含CAD圖紙】
以上為資料預覽概圖，下載文件后為壓縮包資料文件?！厩逦?，無水印，可編輯】dwg后綴為cad圖，doc后綴為word格式，需要請自助下載即可，有疑問可以咨詢QQ 197216396 或 11970985
畢業設計(論文) 課 題 名 稱 線圈高骨架的注塑模具設計 學 生 姓 名 學 號 院(系)、專 指 導 教 師 職 稱 20*年4 月 26日任務書一、 設計課題 線圈骨架注塑模設計二、 工件圖及技術要求圖式：工件圖1. 零件名稱：線圈骨架2. 材 料：聚氯乙烯3. 技術要求：設計一模兩件側澆口注塑模 三、 任務要求1. 材料的工藝成形性能2. 塑件的工藝性分析3. 模具結構設計4. 相關工藝計算5. 完成模具的裝配圖及零件圖的繪制6. 編寫設計說明書摘要 本設計主要講述了以軟聚氯乙烯（SPVC）為材料的線圈高骨架注塑模具的設計過程。此模具在設計時，充分考慮了生產批量、以提高生產效率、降低生產成本為主要宗旨。 本產品為電動機繞線圈，形狀規則，內空心，側有凹槽，其要求它具有耐光，耐化學腐蝕、耐磨。結合這些要求，材料選擇軟聚氯乙烯。根據計算出的體積與質量選擇SZ-100-60型號的注塑機注塑。由于塑件內空心，側有凹槽要求模具必需采用斜導柱側抽芯機構分型。經過比較，采用斜導柱在定模，哈夫塊（斜滑塊）在動模的結構 。整體斜楔定位，斜導柱側抽芯分型，推板推出工件的工作原理。設計中對主要零件一一的進行了設計。文中插入了非標準零件圖，以及模具結構圖。AbstractIs it tell taking soft polyvinyl chloride (SPVC ) as material coil high skeleton mould plastics idea course of mould mainly to design originally. This mould is in the design, fully consider production lot , regard improving production efficiency , reducing the production cost as the main aim.This product winds the coil for the motor, form rule, hollow inside, the side has grooves , it requires it is able to bear all, able to bear chemistry and corroded, wear-resisting . Combine these require material choose the soft polyvinyl chloride. Choose the moulding plastics machine of SZ-100-60 type to mould plastics according to the volume and quality calculated out. Mould piece hollow , side have groove demand mould must adopt oblique to lead post side release the core organization dividing into type. Through compare, adopt oblique to lead post make mould , Haff piece (oblique to slip yuan ) Move the structure of the mould . Whole oblique wedge make a reservation, oblique to lead post side release core person who divide , push board put out operation principle of work piece.To the designing one by one of major part in the design. Have inserted the non-standard part picture, and mould structure chart in the article.目 錄摘要 IAbstract II 前言 1第1章 塑件分析 2第1.1節 塑件工藝性能分析 2第1.2節 塑件批量 2第1.3節 塑件批量體量和質量 3第2章 注塑機的選擇 4第2.1節 注塑機的概述 4第2.2節 選擇注塑機 6第3章 模具設計的有關計算 6第3.1節 成型零件工作尺寸的計算 6第3.2節 成型腔壁厚的計算 8第4章 模具結構的設計 9第4.1節 澆注系統的設計 9第4.2節 模具結構草案 14第4.3節 合模導向機構設計16第4.4節 塑件脫模機構設計18第4.5節 側向分型與抽芯機構設計18第4.6節 模具溫度調節系統22第5章 注塑機參數的校核 23第5.1節 最大注塑量的校核23第5.2節 注塑壓力的校核23第5.3節 鎖模力的校核24第5.4節 模具與注塑機安裝部分相關尺寸校核24第5.5節 開模行程和頂出裝置的校核25結論 26參考文獻 27符號說明 28致謝 30畢業設計任務書一、 設計課題 線圈骨架注塑模二、 工件圖及技術要求圖式：工件圖1. 零件名稱：線圈骨架2. 材 料：聚氯乙烯3. 技術要求：設計一模兩件側澆口注塑模 三、 任務要求1. 材料的工藝成形性能2. 塑件的工藝性分析3. 模具結構設計4. 相關工藝計算5. 完成模具的裝配圖及零件圖的繪制6. 編寫設計說明書 外文翻譯外文翻譯原文：Injection Molding Many different processes are used to transform plastic granules, powders, and liquids into product. The plastic material is in moldable form, and is adaptable to various forming methods. In most cases thermosetting materials require other methods of forming. This is recognized by the fact that thermoplastics are usually heated to a soft state and then reshaped before cooling. Theromosets, on the other hand have not yet been polymerized before processing, and the chemical reaction takes place during the process, usually through heat, a catalyst, or pressure. It is important to remember this concept while studying the plastics manufacturing processes and polymers used. Injection molding is by far the most widely used process of forming thermoplastic materials. It is also one of the oldest. Currently injection molding accounts for 30% of all plastics resin consumption. Since raw material can be converted by a single procedure, injection molding is suitable for mass production of plastics articles and automated one-step production of complex geometries. In most cases, finishing is not necessary. Typical products include toys, automotive parts, household articles, and consumer electronics goods.Since injection molding has a number of interdependent variables, it is a process of considerable complexity. The success of the injection molding operation is dependent not only in the proper setup of the machine hydraulics, barrel temperature variations, and changes in material viscosity. Increasing shot-to-shot repeatability of machine variables helps produce parts with tighter tolerance, lowers the level of rejects, and increases product quality (i.e., appearance and serviceability).The principal objective of any molding operation is the manufacture of products: to a specific quality level, in the shortest time, and using repeatable and fully automatic cycle. Molders strive to reduce or eliminate rejected parts in molding production. For injection molding of high precision optical parts, or parts with a high added value such as appliance cases, the payoff of reduced rejects is high.A typical injection molding cycle or sequence consists of five phases;1. Injection or mold filling2. Packing or compression3. Holding 4. Cooling5. Part ejectionPlastic granules are fed into the hopper and through an in the injection cylinder where they are carried forward by the rotating screw. The rotation of the screw forces the granules under high pressure against the heated walls of the cylinder causing them to melt. As the pressure building up, the rotating screw is forced backward until enough plastic has accumulated to make the shot. The injection ram (or screw) forces molten plastic from the barrel, through the nozzle, sprue and runner system, and finally into the mold cavities. During injection, the mold cavity is filled volumetrically. When the plastic contacts the cold mold surfaces, it solidifies (freezes) rapidly to produce the skin layer. Since the core remains in the molten state, plastic follows through the core to complete mold filling. Typically, the cavity is filled to 95%98% during injection. Then the molding process is switched over to the packing phase.Even as the cavity is filled, the molten plastic begins to cool. Since the cooling plastic contracts or shrinks, it gives rise to defects such as sink marks, voids, and dimensional instabilities. To compensate for shrinkage, addition plastic is forced into the cavity. Once the cavity is packed, pressure applied to the melt prevents molten plastic inside the cavity from back flowing out through the gate. The pressure must be applied until the gate solidifies. The process can be divided into two steps (packing and holding) or may be encompassed in one step(holding or second stage). During packing, melt forced into the cavity by the packing pressure compensates for shrinkage. With holding, the pressure merely prevents back flow of the polymer malt.After the holding stage is completed, the cooling phase starts. During, the part is held in the mold for specified period. The duration of the cooling phase depends primarily on the material properties and the part thickness. Typically, the part temperature must cool below the materials ejection temperature. While cooling the part, the machine plasticates melt for the next cycle.The polymer is subjected to shearing action as well as the condition of the energy from the heater bands. Once the short is made, plastication ceases. This should occur immediately before the end of the cooling phase. Then the mold opens and the part is ejected. When polymers are fabricated into useful articles they are referred to as plastics, rubbers, and fibers. Some polymers, for example, cotton and wool, occur naturally, but the great majority of commercial products are synthetic in origin. A list of the names of the better known materials would include Bakelite, Dacron, Nylon, Celanese, Orlon, and Styron.Previous to 1930 the use of synthetic polymers was not widespread. However, they should not be classified as new materials for many of them were known in the latter half of the nineteenth century. The failure to develop them during this period was due, in part, to a lack of understanding of their properties, in particular, the problem of the structure of polymers was the subject of much fruitless controversy.Two events of the twentieth century catapulted polymers into a position of worldwide importance. The first of these was the successful commercial production of the plastic now known as Bakelite. Its industrial usefulness was demonstrated in1912 and in the next succeeding years. Today Bakelite is high on the list of important synthetic products. Before 1912 materials made from cellulose were available, but their manufacture never provided the incentive for new work in the polymer field such as occurred after the advent of Bakelite. The second event was concerned with fundamental studies of the nature polymers by Staudinger in Europe and by Carohers, who worked with the Du Pont company in Delaware. A greater part of the studies were made during the 1920s. Staudingers work was primarily fundamental. Carothers achievements led to the development of our present huge plastics industry by causing an awakening of interest in polymer chemistry, an interest which is still strongly apparent today. The Nature of ThermodynamicsThermodynamics is one of the most important areas of engineering science used to explain how most things work, why some things do not the way that they were intended, and why others things just cannot possibly work at all. It is a key part of the science engineers use to design automotive engines, heat pumps, rocket motors, power stations, gas turbines, air conditioners, super-conducting transmission lines, solar heating systems, etc. Thermodynamics centers about the notions of energy, the idea that energy is conserved is the first low of thermodynamics. It is starting point for the science of thermodynamics is entropy; entropy provides a means for determining if a process is possible.This idea is the basis for the second low of thermodynamics. It also provides the basis for an engineering analysis in which one calculates the maximum amount of useful that can be obtained from a given energy source, or the minimum amount of power input required to do a certain task.A clear understanding of the ideas of entropy is essential for one who needs to use thermodynamics in engineering analysis. Scientists are interested in using thermodynamics to predict and relate the properties of matter; engineers are interested in using this data, together with the basic ideas of energy conservation and entropy production, to analyze the behavior of complex technological systems.There is an example of the sort of system of interest to engineers, a large central power stations. In this particular plant the energy source is petroleum in one of several forms, or sometimes natural gas, and the plant is to convert as much of this energy as possible to electric energy and to send this energy down the transmission line.Simply expressed, the plant does this by boiling water and using the steam to turn a turbine which turns an electric generator.The simplest such power plants are able to convert only about 25 percent of the fuel energy to electric energy. But this particular plant converts approximately 40 percent; it has been ingeniously designed through careful application of the basic principles of thermodynamics to the hundreds of components in the system.The design engineers who made these calculations used data on the properties of steam developed by physical chemists who in turn used experimental measurements in concert with thermodynamics theory to develop the property data.Plants presently being studied could convert as much as 55 percent of the fuel energy to electric energy, if they indeed perform as predicted by thermodynamics analysis. The rule that the spontaneous flow of heat is always from hotter to cooler objects is a new physical idea. There is noting in the energy conservation principle or in any other law of nature that specifies for us the direction of heat flow. If energy were to flow spontaneously from a block of ice to a surrounding volume of water, this could occur in complete accord with energy conservation. But such a process never happens. This idea is the substance of the second law of thermodynamics.Clear, a refrigerator, which is a physical system used in kitchen refrigerators, freezers, and air-conditioning units must obey not only the first law (energy conservation) but the second law as well.To see why the second law is not violated by a refrigerator, we must be careful in our statement of law. The second law of thermodynamics says, in effect, that heat never flows spontaneously from a cooler to a hotter object.Or, alternatively, heat can flow from a cooler to a hotter object only as a result of work done by an external agency. We now see the distinction between an everyday spontaneous process, such as the flow of heat from the inside to the outside of a refrigerator.In the water-ice system, the exchange of energy takes place spontaneously and the flow of heat always proceeds from the water to the ice. The water gives up energy and becomes cooler while the ice receives energy and melts.In a refrigerator, on the other hand, the exchange of energy is not spontaneous. Work provided by an external agency is necessary to reverse the natural flow of heat and cool the interior at the expense of further heating the warmer surroundings. 譯文：塑料注射成型許多不同的加工過程習慣于把塑料顆粒、粉末和液體轉化成最終產品。塑料材料用模具成型，并且適合用多種方式成型。在大多數情況下，熱塑性材料可以用許多方法成型，但熱固性塑料需要用其他方法成型。對于熱塑性材料有這種事實的認識，它常常被加熱成為另一種柔軟狀態，然后在冷卻以前成型。對于熱固性塑料，換句話說，在它加工以前還沒有形成聚合物，在化學反應加工過程中發生變化，如通過加熱、催化劑或壓力處理。記住這個概念在學習塑料加工過程和聚合物的形成是很重要的。塑料注射成型越來越廣泛地運用于熱塑性材料的成型工藝。它也是最古老的一種方式。突然間，塑料注射成型材料占所有成型材料消費的30%。塑料注射成型適合于大批量生產，當原材料被成單一的步驟轉換成為塑料物品和單步自動化的復雜幾何形狀制品。在大多數情況下，對于這樣的制品，精加工是不需要的。所生產的各種各樣的產品包括：玩具、汽車配件、家用物品和電子消費物品。因?yàn)樗芰献⑸淠＞哂泻芏嘁鬃兊南嗷ビ绊?，那是一種復雜的虛慎重考慮的加工過程。塑料注射模具設備的成功是不依賴于機器變化到恰當?shù)牟襟E，只有淘汰了需要注射變化的機器，才會導致適應液壓變化、料筒溫度變化和材料黏度變化的機器的產生。增加機器重復注射的能力的變化可以幫助減少公差，降低次品等級和增加產品質量。對于任何模具注射設備的操作人員目的是制造產品，成為特等品、用最短的時間、用重復精度和全自動化生產作為周期。模塑人員在生產過程中總是想盡辦法降低或消除不合格產品。對于塑料注射模具有高要求的光學制品，或者有高附加值的制品如：家用電器制品，它的利潤大大降低。一種塑料注射模具的生產周期或順序由五個階段組成：注射或填充模具補料或壓縮保壓冷卻局部注射塑料顆粒被投入料斗并且打開塑料注射料筒，在那里顆粒被旋轉螺桿帶動進入料筒。螺桿的旋轉強迫塑料顆粒在高壓下擠壓料筒筒壁導致它變成熔體。隨著壓力的增加，旋轉螺桿被迫后退直到有足夠的塑料被注射成為儲料。塑料螺桿強迫熔融的塑料從料筒流到噴嘴、主流道經澆注系統，最終進入模具型腔。當注射模具型腔容積被充滿。當塑料接觸冷的模具表面，它被固化以減少表層。當模具保持熔融狀態，塑料沿著模芯充滿整個模具。，利用率特別高，在注射時型腔被充滿95%98%。接著成型過程進入補料階段。當型腔被充滿，熔融塑料便開始冷卻。冷卻塑料的收縮，就增加了諸如凹痕、孔洞和尺寸不穩定等制品缺陷的發生。為了補償收縮，增加塑料壓入型腔。當型腔被封裹，為防止的熔融狀態塑料從型腔內流向出口，把壓力應用于熔體。這種壓力必須應用直到出口為固態。這種加工可分為兩步（補料和保壓）或可能包含成為一步（保壓或第二階段）。在補料時，熔體被補料壓力收縮補償壓入型腔。在保壓時，壓力僅僅防止聚合物回流。在保壓階段完成以后，冷卻階段開始。在冷卻時，是制品在型腔內保持需具體說明的一個階段。在冷卻持久的階段主要依靠材料的特性和制品的收縮率。典型的，制品溫度必須冷卻到材料的注射溫度。在冷卻制品時，這種機器塑料熔體被冷卻到下一個周期。聚合物是以剪切作用為主題的，如同加熱圈獲得能量一樣。當注射開始，到塑料注射終止。聚合物會立刻出現在冷卻階段以前，直到模具打開和制品被注射。當聚合物被編制成有用的文章，它們被稱為：塑料、橡膠和纖維。許多聚合物，例如棉花和羊毛來自自然，但是絕大多數商業的產品都是人造的，都來源于此。一系列眾所周知的材料包括酚醛塑料，滌綸，尼龍，聚硅氧烷，有機玻璃，纖維素，聚丙乙烯和特氟隆。在1930年以前，商業用的聚合物沒有廣泛應用。然而它們本應該作為新材料在19世紀下半葉出名，卻沒有成功。在該期間，它們所以未能發展，部分原因是不了解它們的性質，特別是，聚合物結構曾是許多無結果爭論的主題。二十世紀的兩次事件使聚合物聲名雀起，并且在世界范圍內占據了很重要的地位。第一次是成功的商業塑料產品叫做酚醛塑料。它有用的工業價值在1912年表現得近乎瘋狂，并且在以后許多年發揮著巨大的價值。今天，酚醛塑料仍然在一系列的人造的產品中占有一席之地。在1912年以前，由塑料制造的材料是有用的，但是那種材料的制造從未提供像發明了酚醛塑料以后，形成新聚合物的動力那樣有價值。第二次事件與基礎學科的自然聚合物有關，被歐洲的史濤丁格和美國的卡羅瑟夫發現，他們在特達華州的杜邦公司工作。一些重要的研究在20世紀20年代被開展，史濤丁格主要從事基礎工作。卡羅瑟夫的成功導致了我們目前巨大塑料工業的發展，引起了對化學聚合物的關注，并且在今天仍然引起了強烈而明顯的關注。熱力學的性質熱力學是工程科學最重要的領域之一。這門科學是用來解釋大多數東西是如何做功的，有些東西為什么不按所預期的那樣做功，另外一些東西又為什么根本不做功。熱力學是工程師在設計汽車發動機、熱泵、火箭發動機、發電站燃汽輪機、空氣調節器、超導電輸電線，太陽能加熱系統等所用的科學知識的關鍵部分。熱力學以能的各種概念為中心，能量守恒這一概念是熱力學的第一定律。這是熱力學以及工程分析的起點，熱力學的第二個要領是熵；熵提供一種用以確定某一過程是否可行的手段。產生熵的過程是可行的，消滅熵的過程是不可行的，這個要領是熱力學第二定律的基礎。他還為一種工程分析奠定了基礎，在這種工程分析中，人們可以算出從給定的能源中所能獲得的有用功率的最大值，或算出做某種工作所能獲得的有用功率的最小值。若要在工程分析中應用熱力學，就必須對能和熵這些概念有一個清楚的了解?？茖W(xué)家關心的是利用這些數據，結合能量守恒及熵的產生這些基本概念來分析復雜系統性能。舉一個工程師感興趣的例子一個大型中心發電站。在該發電站，能源是某種形式的石油，有時是天然氣；該發電站的作用是把燃料能盡可能地轉化成電能，并把電能沿輸電線輸送出去。簡單的說，該發電站的發電方式是：使水沸騰，利用蒸汽轉動汽輪機，汽輪機再轉動發電機。這類發電站中最簡單的只能把大約25%的燃料轉化成電能。但該發電站卻能把大約40%的燃料轉化成電能，這是因?yàn)樵摪l(fā)電站是經過精心設計的結果，把熱力學的基本原理仔細的用于該系統內的數百個零部件。進行這些計算的設計工程師，利用了由物理學家研究出來的有關蒸汽特性的數據；而物理學家則是利用實驗測得的數據，結合熱力學理論，研究出這種特性的數據的。目前在研究中的一些發電站，如果說的確按熱力學分析所預測的那樣工作，可以將多達55%的燃料能轉化成電能。熱始終是自發的從較熱的物體流向較冷的物體，這一規律是一種新的物理概念。在能量守恒原理中或其他任何一種自然規律中，沒有給我們規定熱的方向。如果能量能自發的從冰塊流向周圍的水中，這可能和能量的守恒完全一致，但這一過程決不發生。這一概念是熱力學第二定律的實質。很明顯，冷凍機是一種物理系統，用于廚房的電冰箱、冷場庫和空調裝置，它不僅必須遵從第一定律（能量守恒）也必須遵從第二定律。為了弄清冷凍機為什么沒有違背第二定律，必須對這一定律加以說明，熱力學第二定律實質上是說：熱不會自發地從較冷的物體流向較熱的物體。換句話說，熱之所以能從較冷的物體流向較熱的物體，是外界力量做功的結果，現在我們弄清了某一日常的自然過程。如水和冰之間的熱流動和冷凍機熱從里面向外面流動之間的區別。在水、冰系統中，能量的交換是自發產生的，因而熱的流動是水流向冰。水放出了能量從而變冷，而冰吸收熱量從而融化。另一方面，在冷凍機中，能量交換不是自發產生的，而需要改變熱的流動方向，并通過進一步加熱較暖的周圍環境而使冷凍機內部變冷，就必須依靠外力做功。
收藏