沖壓機床液壓控制系統設計

沖壓機床液壓控制系統設計,沖壓,機床,液壓,控制系統,設計 南京理工大學泰州科技學院 畢業設計說明書(論文) 作 者: 陸輝 學 號： 05010127 系　部: 機械工程系 專 業: 機械工程及自動化 題 目: 沖壓機床液壓控制系統設計 高級工程師 張衛 指導者： 評閱者： 2009 年 6 月 畢業設計說明書（論文）中文摘要 液壓機是沖壓機床的重要組成部分之一，由于傳統試驗法成本高、效率低、系統動態分析復雜，一直是液壓機設計的瓶頸。 本文首先針對3150KN四柱式液壓機液壓控制系統性能的要求，提出了該系統總體設計方案，初步確定了系統各回路的基本結構及主要元件選型；進而，以AMEsim為仿真平臺進行液壓系統建模，并對該系統進行了動態性能仿真，發現了系統初步設計中存在著壓力沖擊大及回程速度慢兩個問題，最后提出了增加釋壓回路和增大工作缸活塞桿直徑的兩個解決方案以解決問題，從而達到優化系統、縮短設計周期和提高系統穩定性的目的。 關鍵詞 沖壓機床 液壓機 液壓控制系統 仿真 畢業設計說明書（論文）外文摘要 Title Modeling and Simulation of Punching Machine Hydraulic Control System Abstract Hydraulic Presses is one of most the important part of the punching machine.Due to the high cost,low efficient and complicated of traditional try-error test,the dynamic analyse and evaluate of the system always is the bottle-neck of the design of hydraulic presses. Firstly,aimed at the requirement of the performance of the hydraulic control system of 3150KN type four-pillars hydraulic machine,overall design of this system was proposed.Furthermore the configuration of loops,the type of main components were given.Moreover it was modeled with AMESim.By dynamic simulation of system,the problems such as excessive pressure impact and too slow return rate exist in preliminary design were found.Finaly,additional a pressure-release loop and inrease the diameter of the rod were put forward as solutions to solve those problems. Therefore,the purpose of optimizing system,shorting design cycle and improving the stability of system can be achieved. Keywords Punching machine Hydraulic presses Hydraulic control system simulation