遙控車設計【遙控智能小車】【輪式機器人】

遙控車設計【遙控智能小車】【輪式機器人】,遙控智能小車,輪式機器人,遙控車設計【遙控智能小車】【輪式機器人】,遙控,設計,智能,小車,輪式,機器人 TV broadcast bodywork design requirementsIntroduce bodywork design Install broadcast is a comprehensive system engineering, the body is the complex system is an important part of. In the broadcast, the body part in carrying out all broadcast video recording needed, audio and peripheral equipment, provide an outside the workplace. Not only such, still must ensure the safety equipmentoperation and smooth transhipment, The design quality, not only directly affect the task of broadcast programs, but also to the whole system of safe transport equipment.Bodywork design, is the first consideration in the broadcast of the design, the first thing to do, It will have a direct relationship to other system design.Bodywork designing technical requirements for design, should according to the hull of broadcast equipment size and purpose to choose, The general is installed cameras number, the risk is bigger also. According to the former chapter 8, use the broadcast cameras, can consider to choose medium broadcast. In television broadcast often faced severe external environment, and considering carrying equipment and broadcast task too many factors such as particularity, broadcast in the modification of car when the car to the body, structure and so on a series of chassis project careful overall consideration, through special design and processing, can meet the basic requirements of television. The following are the technical requirements for design body.The safety performance of the broadcast must conform to the state auto industry standards, car body processing and chassis USES the overseas broadcast depot exterior processing technology, size and payload must conform to the state department of traffic regulations. Car chassis and selection: international famous brand high-end products, the truck chassis on all equipment shall be loaded under the condition of the truck with 20% less than 200 surplus, engine, air suspension design, power electronic speed, hydraulic control 85KM/h, air conditioning system design, driving with anti-lock brakes (ABS) emission standards, with European standards, 111 2.5 meters wide.Car body requirements: TiZong compartments 10-11 meters long, no more than is 3.8 meters high and wide 2.5 meters, the right side is four meters long pull box. Box body use fixed number of year more than 15 years, the car body structure of aluminum alloy frame, with high strength and insulation, Material requirement is accord with international standard of environmental protection, flame retardant materials. Vehicle requirements, dustproof, waterproof and sealed anti-rust, anticorrosion, preventing electromagnetic interference, antistatic, After the integration of box body must be rain experiment (including the side after pulling open box, when jose) experiments, the static pressure side tilt impact experiment. The surface with high strength and durable products in the process of paint, paint baking room. Body after processing, vehicle has left from the Angle, finally, from the smallest drive vehicle spacing, minimum turning radius basic technical parameters.Body: the space layout design requirements, and fully consider the reasonable layout of the camera, lens, earphone, tripod, cable, microphone, tools and equipment accessories storage space. For the car fixed equipment should consider appropriate carry scheme.In the national standard of vehicles, within the scope of the space as far as possible, spacious internal headroom maximization, the lateral pull section 2.2 meters, internal clear part and internal headroom wife 2.0 cars, cars GaoCheng 4 meters in vitro.According to the different type of programme production division, scientific and reasonable utilization of working space. The workspace shouldHave partition, and pass the adornment with door, audio broadcasting acoustic requirements.Car chassis and selectionGenerally speaking, the car chassis and is generally together of choose and buy, the first to calculate the weight, then the broadcast and calculate the maximum weight, total quality, Choose total capacity calculation model is bigger than that.This design calculation, for example (hereinafter data for each half xiang estimated) :The total weight of two car electronic equipment nominal total weight (1 ton) + internal cables and connectors total weight (0.3 tons) ten outsideCable and cable reels total weight (0.5 tons of air-conditioning equipment and power) and total weight (l) + containing side and tons of heavy trunk TiZong compartments (5 tons) + car chassis total weight (5.5 tons) = 13.8 tons. Maximum loading 17.25 tons.Additionally, want to consider the traffic situation and task destination of local geography environment, For been poor road conditions or the environment, should choose the output power of the engine and have left corner to corner and Outlines the chassis (in after modification, this part of the parameters change), In order to protect the precision bearing, should choose the equipment with air suspension design of air suspension system (increase chassis, can effectively increase the stability and the operation is necessary in the smallest increase car from the ground clearance and increase the car go right Angle of comparison, through calculation. Head and chassis selection for: Germany, MANLE18.280 car chassis and 18 tons, the highest quality of loading, electronic power output of 280 horsepower maximum speed did 85k: / h, exhaust emission standard requirements, chassis for double-axis braking, rear suspension system (air adjusting range to 14Omm - 80mm), to 18.5 Angle (left), (6.5 Angle, hydraulic steering system, ABS system.Bodywork design types and carsBody type selection, according to the technical requirements for broadcast medium body choice to build. At present, we have the choice of two types: the body dragged hang cabinet type body and direct box type bodywork. Straight hang cabinet is cabinet of body directly placed in vehicle chassis. Drag hanging box type body is only a few on-axis (l), or on the trailer to move. Now broadcast and dimensions of the body, but are strict standard practice. Straight hang cabinet body type hanging box type than drag of small size, because the body size by means of transport together for this decision, countries have limited body length. Generally speaking, it adopts the body from 8 to 10 metres, car - 10-12 meters to. Drag hang cabinet type body USES is 13.6 meters standards body length, but due to the design needs may be more or less. For example, do the length of 18 meters above the hull. Considering the high road, there is through the general standard limits, cannot exceed 4 meters high, usually for 3.7-390 meters, width is 2.5 meters. Because of this part of the city and the surrounding roads are narrow, many sites around the gate, and narrow space, low broadcast to think of site near the area is restricted, models. Additionally, the demand is moderate, considering the number of these factors, so the choice of pull with lateral direct box type car. Hang cabinet type body straight by lateral pull cars, can expand workspace technology area, reduce the length of the body and the height, make whole have shorter turning radius, and good road through sex, increase flexibility of moving body. Drag hanging bodywork, high center of gravity, stability, not only in the city driving speed is slow, even in the highway is compared with straight, and drag hang trailer for highway and car case typed driver requirement is high. However, until the body hangs box type, the car chassis and broadcast is permanently connected compartment, Because of the reliability of the car and car box part is the reliability of the chassis, therefore the reliability of the system reliability of normal operation. However, in the car with tow lock, in case.Car body designThe whole system design is compartments of the follow-up work, it relates to broadcast other system design. In the initial stage of design, construction, as a first consideration should choose the material, then compartments of air conditioning, consider bodywork layout and installation requirements of technical equipment, etc; put At the same time, the design details must be considered the perfect follow-up function. The car body from design to completion, need at least 4 to 5 months. Various processes are certain order, therefore, in the design of the system should have planning and management. Car layout. The car compartment, broadcast early material body USES a lot of hardwood as their framework with the period, the most commercial body design, In the 1960s began to aluminum frame, aluminum envelope special design direction. 4 when turning radius: automotive steering wheel steering, car outside the center, under support vehicles, track circle radius. Steering wheel turned to limit position for minimum radius of turn ramming turn radius of glory. Now, a better and more stable fiber materials of aluminium surface (aluminum) chromate salt a sandwich board structure of interlining, Therefore, most use these new materials and structure to build the whole body, the conventional materials is added as internal store content ark, entrances, and other auxiliary area.Through the comparison, FRP (GRP6 or FRP6) or aluminium surface material qualitative sheet intercalation sandwiches are high, with design, long service life, magnetic, insulation, sound insulation, etc.Sandwich board, according to the different surface material, is divided into: steel surface materials and aluminum/GRP surface materials. When the materials of large area, steel surface material can produce vertical crease, and aluminum/GRP surface materials (not crease) consecutive. In addition, the surface of aluminum excellent in reason, including anodized, apparent into processing, coating and electroplating, therefore, to broadcast, choose aluminium surface or surface suitable materials.For frame materials (stainless steel and aluminium), we fully consider the various factors. Stainless steel welding joint with high mechanical strength, rigidity and fatigue resistance, can satisfy the demand for hull integrity structure. Among the austenitic stainless steel, with excellent energy absorption ability, considering safety construction, it is elected. In the vehicle weight after comparison, choose steel material than aluminum material slightly heavier 10%. Through comparing, aluminum plate type: the surface of metal sheet intercalation sandwiches and mixed structure of the body. This bodywork austenitic stainless steel body frame structure (profiles do using stainless steel welding aluminum easier than because of stainless steel, aluminum) sandwiches sandwich plate surface of car do. For Windows and doors, choose body surface sandwich sandwich plate GRP. Box body side sandwich sandwich plate thickness 50 cars, total body top sheet intercalation 55mm thick sandwiches, the total volume of reinforcement and the cabins lockers by certain thickness of stainless steel. This new design of body structure, give full play to the advantages of two kinds of materials, and make a new body than the current domestic other body, has more advantages than traditional vehicle weight of car-body reduce 40%, Aluminum/GRP materials sandwich insulation sandwich board, make car is very quiet, Body structure is due to decorate, Car body USES sandwich plate containing special since maintain sandwich super structure, high strength, good resistance to impact and the support ability, to ensure the long-term stability of the hull structure, can reduce maintenance costs. In addition, sophisticatedelectronics wooden store content ark, the table at the edge of the wooden edge material selection, was processed by the hardwood, insect and moistureproof, Rappel/abseil stations should be at the man-made fabrics such as screen window instead of natural.The design and processing of carriageWhen a detailed schedule chart, after the completion of the body frame can from inside to outside began to build. From the bodywork design to completion probably need 4-5 months, then consider all equipment purchase, If the plan is completed in body, thoughtful, you can install equipment. At the beginning of the process, frame first is fixed on the car chassis rack. For special car body, chassis rack and body between the special elastic adhesive filling, can guarantee the bodywork multiple components in their long remain relatively fixed position, extended body life. When the body, the engineer will cabins sandwich plate design requirements by large Windows, doors and maintenance (etc), calculated platform, dig, then without fixed whole car chassis. For different area, we adopt profiles between sheet buckles after heightenning strength the special adhesive elastic method, minimum connection screw fastening and reduce the use of welding, hardware are stainless steel. In addition, in need of welding, choose good welding materials electroplating. On roof and floor, also used similar plank and processing method, But in these areas under the floor and big flower board inside, must design the air conditioning intake on spear strike price, exhaust pipe and cable etc. Air inlet 11 feet by ten working area through porous ceiling is completed, therefore essential in insulation layer under the appropriate design of pipe, In the porous metal plate, aluminum materials, and should choose the eye. The air filter condensation prevention. In order to avoid air turbulence generated in pipe noise, the design of many such pipe, the number of air conditioning, these specifications depending on pipes adopts non-toxic ammoniac Yun foam body. For simplified equipment maintenance, design the level off and maintenance. After repair, below half open platform made floor, ceiling upper, which makes it very convenient maintenance maintenance personnel. Maintain doors equipped with gas leading hoop, can easily open doors: all of the mouth, and the dust, shimei, and under the unified set with a key can open all the lock of the door. On both sides of the car body skirt locker, design for the camera lens, the tripod, backup, cable, tools and equipment store empty, They are designed to key can open mode. Because the body with cars, so in design and installation of the bottom side pull the two squares retractable cable protection pipe, through the cable from here to the body of internal also should be carefully considered. Within the sound broadcast require special environment, and therefore must choose sound-absorbing materials of wall and ceiling, we choose is porous sound-absorbing board (belong to impedance compound aluminum mufflers), internal filling composite sound-absorbing material. Car floor selects anti-static floor, easy cleaning. In the equipment design, the frame and the console keep back the gap in 50, This is after wiring brought convenient, also increased the equipment of cabinet, in order to control temperature air circulation. For the broadcast from appearance, can choose their own cars in the standard color swatches, so the color to the international standard RAL9010 color car choose pure white (to go out at the camera calibration quick white balance). After the integration, car body 10.06 presidents, total height 3.75 m, width 2.5 m, right side, 4m bandwidth, can pull lm. The manufacturer to rain experiment box body (including the lateral spread), full pull box when inclined to static experiment, high impact experiment, Meet the design requirements. When our car modified in the rear car modification, rear skirt do for design of dress, car tilting such modified normal operation technical parameters for the final horn, left: from high 437mm, driving the minimum distance from the ground. Minimum turning radius, the vehicle 9.65 m.Bodywork layout designThe number of hull layout including partition door, the work area, etc. According to the practice of the body, broadcastIs divided into three separate areas: director area, centralization, audio area. With the setting TV production, more standardized, scientific and set each region also distribution and the corresponding locations.電視轉播車車體的設計要求車體設計介紹安裝轉播車是一項綜合性的系統工程，車體是這個復雜系統的重要組成部分。在整個轉播車中，車體部分承載了所有轉播錄制所需要的視頻、音頻及周邊設備，提供了室外工作的場所。不僅如此，車體還必須保障設備的安全運行和順利轉運;其設計的好壞，不僅直接影響節目制播任務的完成，還關系到運送整個系統設備的安全。車體設計，是在轉播車設計中最先考慮的，也是首先要做的;它的好壞直接關系到以后其他系統的設計。車體設計技術要求車體設計，應該按照轉播車的設備規模和使用目的來選擇;一般是安裝攝像機的訊道數越多，車體也就越大。按照前章所述，使用8臺攝像機的轉播車，可以考慮選擇中型轉播車。鑒于電視轉播車常常面臨的惡劣外部環境，以及考慮到承載設備的嬌貴性和轉播任務的特殊性等諸多因素，轉播車車體在改裝時必須對車的底盤、車體結構等一系列項目進行周密的全盤考慮，通過特殊設計和精心加工，才能夠滿足電視轉播的基本要求。下面給出車體設計的技術要求。轉播車的安全性能必須符合國家汽車行業的相關標準，車廂體加工及底盤采用國外轉播車廠加工技術，外型尺寸及有效載荷必須符合國家交通部門的相關法規。車頭和底盤選型要求:國際知名品牌的高端產品，底盤的載重應在裝載所有設備的情況下留有20%以上的載重余量，引擎不小于200馬力，空氣懸掛設計，電子限速85KM/h，液壓控制駕駛系統，空調設計，配備ABS(剎車防抱死)，尾氣排放標準符合歐標準，車寬2.5米。車廂體要求:廂體總長10-11米，整車高不超過3.8米，寬2.5米，右部有4米長的側拉箱。廂體使用年限十五年以上，車廂體框架由鋁合金夾層結構組成，有較高的強度和絕緣性;所用材料要求是符合國際標準的環保、阻燃材料。整車要求密封，防塵、防水、防銹、防腐蝕，防電磁干擾、防靜電;集成后必須對廂體進行淋雨實驗(包括側拉箱展開后)，滿荷時進行靜態側傾斜實驗，防高壓沖擊實驗。外表面采用環保型高強度耐用產品油漆，整個噴漆過程在烤漆房進行。車體加工后，要求車輛有合適的離去角、最后端離地高、行駛中最小離地間距、整車最小轉彎半徑等基本技術參數。車體布局設計要求:空間布局合理，并充分考慮攝像機、鏡頭、耳機、三腳架、備用線纜、話筒、工具等設備器材及其附件的存放空間。對于非車內固定設備應當考慮合適的攜帶方案。在國家車輛標準范圍內，空間盡可能的寬敞，車廂體內部凈高最大化，非側拉部分內部凈高2.2米，側拉廂部分內部凈高妻2.0米，車廂體外高成4米。按照節目制作的不同工種劃分工作區，科學合理的利用空間。各工作區之間應當有隔斷，并有通行門，音頻區的裝飾符合廣播聲學要求。車頭和底盤選型一般來說，車頭和底盤一般是連在一起選購的，首先要計算整個轉播車的載重量，然后加上自重，計算出其最大總質量;選擇總承重略大于計算值的型號叫。以此設計計算為例(以下數據為半湘各估算值):車總重二電子設備標稱總重(1噸)+內部電纜和連接頭總重 (0.3噸)十外部電纜及電纜盤總重 (0.5噸)+空調設備和電源總重(l噸)+含側拉廂后車廂體總重(5噸)+車底盤總重(5.5噸)=13.8噸;最大裝載質量17.25噸。另外，要考慮任務目的地道路通行狀況和當?shù)氐牡乩憝h(huán)境;對于多山地或者道路條件較差的環境，應選擇輸出功率較大的引擎和擁有較大接近角和離去角竺的底盤(在車體改裝后，這部分參數會變化);為了保護承載的精密設備，應選擇帶有空氣懸掛設計的底盤(增加空氣懸掛系統，能有效地增加汽車行運中的穩定性和在必要時增加汽車的最小離地間隙右、加大汽車的離去角。通過計算比較，對車頭和底盤的選型為:德國MANLE18.280車頭和底盤，最大裝載質量18噸，最高輸出功率280馬力，電子行最高車速85k:/h，尾氣排放標準達到要求，底盤為雙軸制動，后橋有空氣懸掛系統(調整范圍到80mm-14Omm)，接近角(18.5)，離去角(6.5)，有液壓助力轉向系統，有ABS系統。車體類型及廂體設計車體類型選擇依據技術要求，此轉播車按照中型車體選擇建造。目前，供我們選擇的車體有兩種類型:拖掛箱體式車體和直掛箱體式車體。直掛箱體式車體是箱體直接被安置在車輛底盤上。拖掛箱體式車體是僅有后軸(l個或幾個)的，靠拖車頭來移動?，F(xiàn)在轉播車車體尺寸并沒有嚴格的標準，但有慣例。直掛箱體式車體要比拖掛箱體式車體的尺寸小，這是因為車體尺寸由連在一起的運輸工具決定，國家對這樣的車體長度有一定的限定。一般來說，它采用的車體從8米到10米之間，車總長達到10- 12米。拖掛箱體式車體采用的是13.6米的標準車體，但長度由于設計的需求可能或多或少。例如，有做到長度達到18米以上的車體?？紤]到道路通過性，高度是有標準限制的，一般不能超過4米，通常的高度為3.7- 3.9米，寬度總是2.5米。由于本市和周邊城市的部分道路比較狹窄，許多場地周圍空間狹小，并且大門較低，轉播車要想到達現場較近的地區工作，車型受到了限制。另外，設需求的訊道數適中，考慮到這些因素，因此選擇了帶側拉廂的直掛箱體式車體。直掛箱體式車體采用側拉廂技術，可以擴大工作空間面積，減小車體的長度和高度，使整車有較小的轉彎半徑，和較好的道路通過性，增加車體移動的靈活性。拖掛式車體龐大、重心較高，故穩定度較差，不僅在市內行車速度慢，即使在高速公路上也難與直掛車相比，還有拖掛箱體式車體對于公路和駕駛員的要求也很高。但是，直掛箱體式車體的轉播車，其車底盤和車廂體是永久連接的;由于車箱體部分的可靠性加上車底盤的可靠性是整個系統的可靠性，因此其正常行駛的可靠性降低了。不過，可以在車內配備拖鎖，以備萬一。車廂體設計廂體設計是整個系統后續工作的基礎，它關系到轉播車其它系統的設計。在廂體設計的最初階段，要首先考慮選擇構造廂體的材料，然后考慮車體布局、空調的需求和安裝、技術設備的擺放等等;同時在設計的細節上，必須考慮后續功能的完善。整個車廂體從設計到完工，至少需要4到5個月。各種工序都是有一定的順序，因此，在設計時要有系統的規劃和管理。車布局圖。車廂體的選材早期，轉播車車廂體使用了大量的硬木作為它們的框架，這跟那個時期多數商用車體設計一致;60年代開始轉向鋁骨架、鋁蒙皮的專用車設計方向。4轉半徑:汽車轉向時，汽車外側轉向輪的中心、下面在車輛支承平面，軌跡圓半徑。轉向盤轉到極限位置時的轉夯半徑為最小轉夸半徑?，F(xiàn)在，有了更好的玻璃鋼材料和更穩定的鋁表面(鋁一鉻酸鹽處理)三明治夾層板材結構的出現;因此，大多采用這些新型材料和結構去構建整個車體，常規材料只是補充用作內部儲物柜、出入口和其他附屬區域。通過比較，玻璃鋼(GRP6或FRP6)或鋁表面材料的三明治夾層板材有輕質高強、具有可設計性、使用壽命長、抗磁、絕緣、隔音等等多種優點。三明治板材，根據表層材料的不同，又分為:鋼表層材料和鋁/GRP表層材料。當材料面積做的過大后，鋼表層材料會產生垂直折痕，而鋁/GRP表層材料連續(沒有折痕)。此外，鋁具有優良之表面處理性，包括陽極處理、表面化成處理、涂覆及電鍍等，因此，對于轉播車來說，選擇鋁表層或表層材料較為合適。對于框架材料(不銹鋼和鋁)的選擇，我們充分考慮了多方因素。不銹鋼焊接的接頭具有很高的機械強度、剛性和抗疲勞性，能滿足對于車體整體性結構的需求。其中奧氏體不銹鋼日具有優秀能量吸收能力，考慮到安全構造，它是當選的材料。在整車成型后重量比較上，選用鋼材料比鋁材料略微重10%。通過綜合比對，車體板材選型為:鋁表層的三明治夾層板材和金屬混合結構的車體。該車體采用奧氏體不銹鋼型材做車身骨架結構(采用不銹鋼材是因為不銹鋼材比鋁合金容易焊接)，用鋁表層的三明治夾層板材做車體板。對于車體窗戶和門，選擇GRP表層的三明治夾層板材。廂體側面三明治夾層板材總厚50mm，廂體頂部三明治夾層板材總厚55mm，整個廂體的加固部分及儲物箱采用一定厚度的不銹鋼。這種新設計的車體結構充分發揮了兩種材料的長處，使新車體比目前國內其它車體，具有更多的優點車體的重量比傳統的車體減輕40%;鋁/GRP材料三明治夾層板材的隔音特性，使車廂內非常安靜;車體由于是框架結構，可隨意布置分區;車廂體采用的三明治板材含有特殊的自維持三明治超級結構，強度高，結構具有很好的抗沖擊和支持能力，保證了車體結構的長期穩定性，可減少維護費用。另外，車體內部木制儲物柜、臺面的邊緣木條鑲邊材料的選擇為，被加工處理過的硬木，以防蟲和防潮;同時紗窗等織品應選人造的而非天然的。車廂體的加工和設計當詳細的一程圖完成后，車體的框架就可以從里至外開始建造了。從車體設計至完工大概需要4至5個月，這時要考慮所有設備的購買;如果計劃考慮周全，在車體完工時，便可安裝設備了。加工的初期，車骨架首先被固定在車底盤的鋼架土。對于特種車車體來說，底盤的鋼架和車體之間采用特殊的彈性粘合劑填充，可以保證車體的多種部件長久地保持在他們相對固定的位置上，延長車體的壽命。廂體時，工程師將大塊三明治板材按設計要求(門、窗和維修平臺等)，計算后，切挖出不用的部分，然后固定全車底盤上。對于不同