液壓挖掘機泵源設計【含CAD圖紙和說明書】

液壓挖掘機泵源設計【含CAD圖紙和說明書】,含CAD圖紙和說明書,液壓,挖掘機,設計,cad,圖紙,以及,說明書,仿單 寧XX大學畢業設計(論文)挖掘機泵源設計所在學院專 業班 級姓 名學 號指導老師 年 月 日摘 要本文主要完成挖掘機泵源系統設計，驅動的液壓系統，它由油箱、濾油器、液壓泵、溢流閥、開停閥、節流閥、換向閥、液壓缸以及連接這些元件的油管組成。它的工作原理：液壓泵由電動機帶動旋轉后，從油箱中吸油。油液經濾油器進入液壓泵，當它從泵中輸出進入壓力管后，將換向閥手柄、開停手柄方向往內的狀態下，通過開停閥、節流閥、換向閥進入液壓缸左腔，推動活塞和工作臺向右移動。這時，液壓缸右腔的油經換向閥和回油管排回油箱。為了克服移動工作臺時所受到的各種阻力，液壓缸必須產生一個足夠大的推力，這個推力是由液壓缸中的油液壓力產生的。要克服的阻力越大，缸中的油液壓力越高；反之壓力就越低。輸入液壓缸的油液是通過節流閥調節的，液壓泵輸出的多余的油液須經溢流閥和回油管排回油箱，這只有在壓力支管中的油液壓力對溢流閥鋼球的作用力等于或略大于溢流閥中彈簧的預緊力時，油液才能頂開溢流閥中的鋼球流回油箱。所以，在系統中液壓泵出口處的油液壓力是由溢流閥決定的，它和缸中的油液壓力不一樣大。關鍵詞：挖掘機, 液壓挖掘機，泵源，液壓站VAbstractThis paper mainly completes the design of excavator hydraulic pump system, the hydraulic drive system, it consists of a tank, oil filter, hydraulic pump, relief valve, stop valve, throttle valve, reversing valve, hydraulic cylinder and connection of these components tubing composition. Its working principle: the hydraulic pump driven by the motor after the rotation, from the oil tank. Oil by the oil filter into the hydraulic pump, when it from the pump output into the pressure pipe, valve handle, stop the direction of a handle to the state, through the open stop valve, throttle valve, reversing valve into the hydraulic cylinder of the left cavity, push the piston and the working table moves to the right. At this time, the right chamber of the hydraulic cylinder oil by reversing valve and return line back to the oil tank. In order to overcome the various drag force when the mobile station is subjected to, the hydraulic cylinder must generate a large enough thrust, which is generated by the oil pressure in the hydraulic cylinder. The higher the resistance, the higher the oil pressure in the cylinder, and the lower the pressure. When the input of the hydraulic cylinder oil is regulated by a throttle valve, the hydraulic pump output of the excess oil shall be the overflow valve and an oil return pipe to the tank platoon, this only in the manifold pressure of the fluid pressure force of a relief valve ball is equal to or slightly larger than the relief valve spring preload and top oil to open overflow valve ball flows back to the tank. Therefore, in the system of hydraulic pump outlet oil pressure is determined by the relief valve, and it and the oil pressure in the cylinder is not as big as.Keywords: excavator, hydraulic excavator, pump source, hydraulic station目 錄摘 要IIAbstractIII目 錄IV第1章 緒論11.1課題背景及目的11.2 液壓挖掘機整機性能11.3 液壓挖掘機結構21.4 液壓挖掘機傳動原理32 挖掘機泵源設計要求與方案52.1設計要求52.2工況分析52.2.1 液壓挖掘工況分析62.2.2 滿斗舉升回斗工況分析82.2.3 卸載工況分析82.2.4 空斗返回工況分析92.2.5 行走時復合動作分析93 挖掘機液壓系統設計113.1 挖掘機的功用和對液壓系統的要求113.2 挖掘機液壓系統分析113.2.1 挖掘機的液壓系統原理圖113.2.2 系統工作分析123.2.3 主要液壓元件在系統中的作用133.3 液壓元件的選用133.3.1 泵的選用133.3.2 液壓閥的選用133.3.3 液壓缸的選用143.3.4 輔助元件的選用144 液壓缸的設計計算和泵的參數計算164.1 液壓缸設計算164.1.1 外負載計算164.1.2 液壓缸結構尺寸計算174.1.3 油缸強度計算184.2 泵的參數計算204.2.1 泵的壓力計算204.2.2 計算所需要的泵的流量214.3 柴油機的選擇224.3.1 泵的驅動功率的計算224.3.2 柴油機的選擇225 液壓集成塊的設計235.1塊式集成的結構245.2塊式集成的特點245.3塊式集成液壓控制裝置的設計256 液壓站的設計296.1液壓站簡介296.2 油箱設計296.2.1油箱有效容積的確定296.2.2 油箱容積的驗算306.2.3 油箱的結構設計326.3 液壓站的結構設計356.4 輔助元件356.4.1 濾油器356.4.2 空氣濾清器366.4.3 液位計376.4.4 液壓油38總結40參考文獻41致 謝42