木制衣架拋光機拋光部分設計含SW三維及14張CAD圖帶開題
木制衣架拋光機拋光部分設計含SW三維及14張CAD圖帶開題,木制,衣架,拋光機,拋光,部分,部份,設計,sw,三維,14,cad,開題
木制衣架拋光機拋光部分設計
摘 要
木制衣架自動拋光機是衣架制造企業的重要加工設備之一。目前國內衣架制造企業大多數還是采用人工拋光的方式。為了提高木制衣架拋光效率，進行了木制衣架拋光機設計，具體內容如下：
本設計基于木制衣架拋光機械的研究現狀和發展?fàn)顩r，根據拋光機的類型、結構特點和工作原理，結合相關設計手冊,對木制衣架自動拋光機進行了結構設計，電動機的選擇，聯軸器的選擇，鍵的選擇，專用夾具的設計，絲桿的選擇及設計，軸承的選用及機構潤滑劑的選用。該木制衣架結構設計緊湊，能基本完成木制衣架的自動拋光。
動力部分由電動機、減速器，輸入軸為主，其余部分參考外購件的參數加以整合設計。而重點設計的是衣架拋光機拋光部分。在計算過程中，軸的設計及絲桿的選用是重點。首先提出拋光機的工作原理，進行結構設計；然后確定一些原始數據，計算出各個軸及絲桿的轉速、功率、轉矩。最后繪制木制衣架拋光機的裝配圖及典型零件的零件圖，對木制衣架拋光機的關鍵參數進行計算和校核。
零件將全部采用solidworks軟件進行計算機輔助設計，設計過程中經過較為精確的測量和計算后將所得的數據進行三維建模，利用模型進行模擬裝配和干涉檢查。構想通過創建三維模型這樣一個平臺來驗證所做的設計，以便于對設計中的細節進行改進。設計完成后，利用Solidworks建立木制衣架拋光機的3D裝配模型；較為逼真地體現外型設計的效果及木制衣架拋光機的主要結構及尺寸關系，繪制二維的零件圖，裝配圖。
關鍵詞：專用夾具；自動拋光；二維工作臺；衣架拋光機。
Abstract
Wooden hanger automatic polishing machine is one of the hanger manufacturing enterprises processing equipment. Domestic hanger manufacturing companies or artificially polished. In order to improve the polishing efficiency of wooden hangers, wooden hangers polishing machine design, as follows:
The design is based on the research status and development of the mechanical polishing of wooden hangers, according to the type of polishing machine, structural characteristics and working principle, combined with the design manual, automatic polishing machine, the structural design of wooden hangers, the choice of motor, coupling the choice of the choice of key, a dedicated fixture design, selection and design of the screw, the bearing selection and institutional lubricant selection. The compact design of the wooden hanger structure, the basic completion of the automatic polishing of wooden hangers.
The dynamic part consists of motor, reducer, the input shaft main, the rest of the reference parameters of the purchased parts to integrate design. Focused on the design of the hanger polishing machine polishing part. In the calculation process, the design of the shaft and screw selection is the key. First proposed polishing machine works, for the structural design; then determine the raw data, calculate each axis and the screw speed, power, and torque. Finally draw a wooden hanger polishing machine assembly drawing and typical component graphs, calculation and check of the key parameters of the wooden hanger polishing machine.
The parts will be using solidworks software for computer-aided design, data more accurate measurements and calculations will be obtained in the design process, 3D modeling, using the model to simulate the assembly and interference checking. Idea to verify the design done by creating three-dimensional model of such a platform, in order to improve on the details of the design. The design is complete, the 3D assembly models that the Solidworks establish wooden hanger polishing machine; more realistically reflect the effect of the exterior design and wooden hangers, polishing machine the main structure and size relationships, draw two-dimensional part drawings, assembly drawings.
Key words:Special fixtures; automatic polishing; two-dimensional bench; hanger polishing machine.
收藏