滾動軸彎曲模設計

滾動軸彎曲模設計,滾動,轉動,彎曲,曲折,設計 滾 動 軸 彎 曲 模 摘 要模具設計思思是學習模具專業課的最終目的，我們主要對沖壓模和塑料模有一定的認識。本次設計主要是對沖壓工藝中的彎曲模進行設計，設計的題目為滾動軸彎模。主要內容： 1） 彎曲零件工藝性分析 2） 彎曲工藝方案的確定3） 模具的主要參數計算以及模具的總體設計4） 模具零件的加工工藝性 5） 模具的裝配，安裝及調試6） 模具設備的選用模具設計的方法及步驟基本上是根據它的內容來決定的，它們之間是相互穿插影響的。通過對彎曲件結構以及沖壓工藝進行分析，初步確定工藝方案，然后對其主要參數進行計算，確定毛坯的尺寸，凸凹模的大小以及壓力機噸位等。對模具進行整體設計后對模具各零件進行裝配。接著在壓力機上安裝并試沖，獲得合格制件標志著模具設計成功。彎曲沖壓模具與沖裁、拉深模之間有很大的區別，它在沖裁的基礎上更由它獨特的方面，較沖裁難，不僅要考慮沖裁力的大小，更重要的是考慮彎曲中容易出現的彎曲回彈和拉裂等一些現象，設計模具時為了保證質量要求需要特別注意考慮工藝性的要求等等。在設計時要注意模具結構簡單、模具使用方便、模具壽命高等問題。并且要提高生產效率，保證產品的質量。關鍵詞：彎曲圓角半徑 彎曲力 凸模圓角半徑 凹模圓角半徑 凸 、凹模間隙 Roll to move the curved song mold of stalk AbstractIt is end purpose that studies the professional lesson of molding tool that molding tool design think, we mainly to hurtle to press the mold and the plastics molds contain certain understanding.A design mainly is to press the bent mold within to carry on the design towards hurtle, the topic of the design for- roll over the stalk curved mold.Main contents：1) flection the spare parts craft analysis 2) the assurance of the flection craft project3) the main parameter calculation of the molding tool and total design of the molding tool4) the molding tool spare parts processes the craft5) the assemble of the molding tool, install and adjust to try6) the molding tool equipments chooses to useThe method and steps of the molding tool design decide according to its contents basically of, they add the influence mutually.Pass to press the craft to carry on the analysis towards curving a structure and hurtling, the initial assurance craft project, then as to its the main parameter carries on the calculation, making sure the size of the semi-finished product, the size and pressure machine tonnage etc. of the convex and cave mold.After carrying on the overall design to the molding tool carry on the assemble to each spare parts of molding tool.Immediately after in the pressure the on board gearing tries also blunt, acquire qualified make the piece to symbolize the molding toolKeyword:Convex and cave mold cleft of the radius cave mold a Cape of the dint convex mold a Cape of a Cape radius flection radius