CK6140數控

CK6140數控,ck6140,數控 摘 要數控車床又稱數字控制（Numbercal control，簡稱NC）機床。它是基于數字控制的，采用了數控技術，是一個裝有程序控制系統的機床。它是由主機，CNC，驅動裝置，數控機床的輔助裝置，編程機及其他一些附屬設備所組成。本次設計課題是CK6140數控臥室車床，CK是數控車床，61是臥式車床，40是床身上最大工件回轉直徑為400mm。此次設計包括機床的總體布局設計，縱向進給設計，其中還包括齒輪模數計算及校核，主軸剛度的校核等。控制系統部分包括步進電機的選用及硬件電路設計和軟件系統設計，說明了芯片的擴展，鍵盤顯示接口的設計等等。關鍵詞 數控機床；開放式數控系統；電動機AbstractThe numerical control lathe called the numerical control (Numbercal control, is called NC) the engine bed. It is based on the numerical control, has used the numerical control technology, is loaded with the procedure control system the engine bed. It is by the main engine, CNC, the drive, the numerical control engine bed auxiliary unit, the programming machine and other some appurtenances is composed.This design topic is the CK6140 numerical control bedroom lathe, CK is the numerical control lathe, 61 is the horizontal lathe, 40 is on the lathe bed the biggest work piece rotation diameter is 400mm.This design including the engine bed overall layout design, longitudinal enters for the design, also includes the gear modulus computation and the examination, the main axle rigidity examination and so on. The control system partially including step-by-steps the electrical machinery to select and the hardware circuit design and the software system design, explained the chip expansion, keyboard demonstration connection design and so on.Key word numerical control tool;Open-architecture;motor目 錄1 總體方案設計1.1 CK6140的現狀和發展1.2 CK6140數控臥式車床的總體方案論證與擬定2 機械部分設計計算說明2.1 主運動部分計算2.1.1 參數的確定2.1.2 傳動設計2.1.3 轉速圖的擬定2.1.4 帶輪直徑和齒輪齒數的確定2.1.5 傳動件的估算和驗算2.1.6 展開圖設計2.1.7 截面圖設計2.2縱向進給運動設計2.2.1 滾珠絲桿副的選擇2.2.2 驅動電機的選用3 控制系統設計3.1繪制控制系統結構框圖3.2.選擇中央處理單元（CPU）的類型3.3存儲器擴展電路設計3.4I/O接口電路及輔助電路設參考文獻謝詞附錄