建筑鋼筋切斷機設計

喜歡這套資料就充值下載吧。資源目錄里展示的都可在線預覽哦。下載后都有，請放心下載，文件全都包含在內，圖紙為CAD格式可編輯，【有疑問咨詢QQ:414951605 或 1304139763】 徐州工程學院畢業設計(論文)摘要鋼筋切斷機是把鋼筋切成所需長度的專用機械在大型建筑工地上的應用非常廣泛。鋼筋切斷機分為機械傳動和液壓傳動兩種。機械傳動式鋼筋切斷機,工作時大都采用電動機經一級三角帶傳動和二級齒輪傳動減速后,帶動曲軸旋轉,曲軸推動連桿使滑塊和動刀片在機座的滑道中作往復直線運動,使活動刀片和固定刀片相錯而切斷鋼筋。 GQ40B型鋼筋切斷機，其剪切運動是由一曲型的曲軸連桿機構完成的。但是由于切斷機機體內腔狹小，在裝配曲軸連桿時比較困難。尤其是在使用中發生故障需要維修時，拆卸曲軸連桿更加不容易，給維修造成很大的不變，因此在不改變設備功能的情況下，我對曲軸連桿機構做了一些改進。改進后的凸輪結構直接從機體航的注冊孔中裝入和取出。而不必拆卸連桿，大大簡化了裝配程序，減輕的工人的勞動強度。同時也極大的方便了維修，還簡化了零件的工藝過程，取得良好的經濟效益。關鍵詞鋼筋切斷機；凸輪；曲軸連桿機構AbstractReinforcing steel cutting machine is to cut the required length of steel machinery specialized for large construction sites in the application of very extensive. Reinforcing steel cutting machine into mechanical transmission and hydraulic transmission of two. Mechanical transmission reinforced cutting machine, working mostly used as a V-belt drive motor and gear drive slow down after two, driven crankshaft rotation, promoting the crankshaft and connecting rod to move the slider blade in the frame of the chute in a reciprocating linear motion So that the activities of the blade and a fixed blade and cut off the wrong steel. GQ40B-steel cutter, cut its movement from one type of linkage to complete the crankshaft. However, due to cut off the small inner cavity of the body, in the assembly when the crankshaft link more difficult. Especially in the use of a fault in need of repair, demolition crank link more difficult to repair a big change, so do not change the function of the equipment under the circumstances, we crank linkage has made some improvement. The improved structure of the cam directly from the body of the aircraft registered in the hole and packed out. Without dismantling the link, greatly simplifies the assembly, reduce labor intensity of workers. But also greatly facilitate the maintenance, has also simplified the process of parts and achieved good economic returns.Keywords Reinforcing steel cutting machine Cam Crankshaft Linkage目錄1緒論11.1鋼筋切斷機的作用11.2鋼筋切斷機的機理11.2.1壓入變形階段11.2.2剪切滑移階段21.2.3剪切滑移階段作用力分析31.2.4剪切全過程剪力分析41.2.5綜合分析41.3鋼筋切斷機理分析71.3.1目前鋼筋切斷機存在的問題91.3.2鋼筋切斷機前景102電動機的選擇112.1計算剪切力P112.2切斷機匹配電動機功率理論計算113減速器的設計133.1傳動比的計算與分配133.2計算傳動裝置的運動和動力參數133.3帶的選擇143.3.1帶的計算143.3.2帶的根數確定153.4齒輪的設計及模數的選擇153.4.1第一級齒輪傳動設計153.4.2第二級齒輪傳動設計方法同第一級設計173.5軸徑的選擇以及軸承的選擇193.5.1軸徑的計算193.5.2軸的校核203.6滾動軸承的選擇計算233.7標準件244連桿的設計255提高強度的幾種方法275.1機體強度提高的設計275.2改變壓刀結構285.3其他部件的改進設計286鋼筋切斷機強度計算參考306.1機體額口的強度計算306.2應力計算316.2.1正應力計算316.2.2計算剪切力P316.3計算剪切力P326.3.1計算正應力326.3.2計算最大應力326.3.3試棒326.4測試方法326.4.1剪切力的測量326.4.2應力測量336.4.3測試結果和理論計算分析情況對比分析337機械式鋼筋切斷機調整及保養的使用357.1鋼筋切斷機的使用調整357.2保養377.3安全一般規定37結論38致謝39參考文獻40附錄41附錄141附錄2464