旋液式油水分離器的設計【含CAD圖紙、說明書】
XIV旋液式油水分離器的設計摘要:目前,水力旋流器在油田采出液預分離和含油污水處理中逐步推廣應用。水力旋流器具有結構簡單緊湊、效 率高、體積及占地面積小等優點。對水力旋流器結構及參數關系進行了分析。通過改進與優選水力旋流器結構,得到旋 流器單體的雙入口結構理想型式為反渦線、大小錐段為圓弧過渡形式。同時簡要分析了高次曲線與正余切曲線結構的 錐段過渡形式,確定出合理的水力旋流器單體旋流腔長度為 65 mm。經過理論研究和對比試驗發現,具有結構參數關系 模型的水力旋流器較常規結構的水力旋流器有更高的分離效率。水力旋流器是利用強離心力場來實現有一定密度差且不互溶物系分離的離心 沉降設備。目前油田在無動力加工環境中的單井作業無法進行機械脫水處理,一 直采用裝原油的容器下加煤炭火燒加溫、攪拌、沉淀、分解的老方法進行脫水處 理。這種方法不但極易引起火災,而且原油損耗大、勞動強度髙、工作效率低, 以及對環境造成極大污染。該方法已經不能滿足現在油田生產的需要。水力旋流法是由英國南安普頓大學(Southampton)研究成功的一種具有 80 年代先進水平的含油污水處理新方法。因?yàn)樗Y(jié)構簡單、分離效率高、成本低,從它問世之日起,就得到了世界各國的重視?,F(xiàn)在,旋流分離已作為重力分離的 一項替代技術,成為世界國際油田地面工程中的主體技術和重要裝備。在前期對液-液旋流分離器流量壓降特性實驗研究的基礎上,分析了結構參數、操作參數及物性參數對液- 液旋流分離效率的影響; 提出了液-液旋流分離器結構設計的設計方法和設計步驟,認為建立性能優良的旋流器模 型數據庫,是選型設計的基礎和前提。關鍵詞 :水力旋流器;分離效率;入口 ;錐段;溢流管;旋流腔;底流管Abstract: At present, the hydrocyclone in oilfield produced gradually promote the use of liquid separation and oily sewage treatment. Hydrocyclone has the XVadvantages of simple and compact structure, high efficiency, small volume and area etc On the relationship between the structure and the parameters of the hydrocyclone are analyzed. Through the improvement and optimization of hydrocyclone, get double entrance structure of ideal type cyclone monomer for the vortex line, size of the taper section is arc transition form. At the same time, a brief analysis of the cone transition form high-order curve and curve structure, reasonable length of single bodied whirl cavity of hydrocyclone has been determined as 65 mm. It has been discovered that through theoretical study and contrast test,the hydrocyclone that possessing relation model of structural parameters hasmore higher separation efficiency than hydrocyclones with conventional structures.Cyclone separators are used in various kinds of industries to separate materials of different densities. By creating a strong swirl, large centrifugal forces in the process mixture are generated and due to differences in density the materials will separate. At present in petroleum industry, single well cannot proceed mechanical dehydration treatments with not power. It always taken heat up and deposit method to dewatering, such means not only bring fire and crude oil waste large, labor intensity high, and it have badly influence on environment. Now that approach had insatiability oil fields produce demand.Hydraulic power method was newly oil-water separation method. It was invented by Britain Southampton University in 1980s. For it structure simplicity, separation efficiency high, and cost low. From it appearance, that has been got widely recognition. In the not far future, rotational flow separate will certainly replace gravitational separation technology, became 21 century international oil field primary equipment.Based on the experiments aiming at studying flowrate and pressure drop performance,geometric parameters, operating parameters and liquid characteristic parameters influence on separate efficiency are analyzed. Optimal structure design method and process of liquid-liquid separate hydrocyclone are brought forward. Its thought that the database of best hydricyclone model is the basic and premises about optimal structure design.XVIKeywords: hydrocyclone; separation efficiency; entrance; conicsection; overflow pipe; whirl cavity; underflow pip
收藏
編號:577727
類型:共享資源
大?。?span id="h8awcug" class="font-tahoma">510.33KB
格式:ZIP
上傳時間:2019-06-13
50
積分
- 關 鍵 詞:
-
旋液式
油水
分離器
設計
cad
圖紙
說明書
仿單
- 資源描述:
-
展開閱讀全文
- 溫馨提示:
1: 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
2: 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
3.本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
5. 裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
裝配圖網所有資源均是用戶自行上傳分享,僅供網友學習交流,未經上傳用戶書面授權,請勿作他用。