帶小圓孔U形筒形件-油箱蓋的沖壓模具設計【拉伸-沖孔復合模含11張CAD圖帶過程卡】
【需要咨詢購買全套設計請加QQ1459919609】圖紙預覽詳情如下：
1油箱蓋沖壓模的設計摘要:本模具設計題目為油箱蓋的落料,拉深,沖孔復合模,此零件需三道工序完成.體現了復雜零件的設計要求,內容及方向.具有一定的設計意義,通過對該零件模具的設計進一步加強了設計者沖壓模具設計的基礎知識,為設計更復雜的沖壓模做好了鋪墊和吸取了更深該的經驗.本設計運用沖壓模具設計與制造工藝基礎知識,首先分析了端蓋零件的外形,尺寸,精度要求,進行了工藝分析,考慮到此零件為圓形零件,對同軸度要求較高,因此采用復合模工藝方案.然后根據零件的外形尺寸計算毛坯總體尺寸,設計排樣圖及計算材料利用率及壓力中心最后計算出工作部分尺寸,模具總體尺寸,總體尺寸包括工作零部件的結構設計,卸料裝置的設計以及固定零件的設計與運用.本模具的特點是推板在彈頂器,頂桿的作用下,處于最上位置,定位板固定坯料,上模部分下降,利用凸凹模和成形推板進行彎曲,上模繼續下降,推動成形推板下降,此時由落料凹模,在成形推板內裝有 6 根頂桿 ,開模時可使工件抬起,便于取件.關鍵詞:拉深模 復合模 凸凹模The Piercing Die Design Of Tank CoverAbstract: This mold design topic for the straining die, falls the material, the punch holes superposable die, this components need three working procedures to complete. Has 2manifested the complex components design request, the content and the direction. Has certain design significance, through further strengthened the elementary knowledge to this components mold design which the designer ramming mold designs, for designed more complex flushes the die to complete the upholstery and to absorb a deeper this experience.This design utilization ramming mold design and the manufacture craft elementary knowledge, has first analyzed the end cover components contour, the size, the precision request, has carried on the craft analysis, considered this components are the circular components, is high to the proper alignment request, therefore uses the superposable die craft plan. Then the basis components external dimensions computation semifinished materials overall size, a design row of specimen map and the computation material use factor and the center of pressure last count is present at work makes the partial sizes, the mold overall size, the overall size including the work spare part structural design, the dumping device design as well as the fixed components design and the utilization.This mold characteristic is the small end cover drawing, falls the material, the punch holes superposable die.The formed push pedal goes against in the ball, under the roof bar function, is in on most the position, the nursery lives the semifinished materials, the top die part drops, the use convex-concave mold and the formed push pedal carry on the drawing and press the shape, the top die continue to drop, impel the formed push pedal to drop, this time by falls the material concave mold, the convex-concave mold carries on falls the material, then flushes the bottom hole. When formed push pedal and dead plate contact, then carries on the reshaping. Is loaded with 6 roof bars in the formed push pedal, operates when the mold may cause the work piece to lift, is advantageous for takes.Key words: The straining die compound die Falls the material convex-concave mold