【溫馨提示】壓縮包內含CAD圖有下方大圖片預覽，下拉即可直觀呈現眼前查看、盡收眼底縱觀。打包內容里dwg后綴的文件為CAD圖，可編輯，無水印，高清圖，壓縮包內文檔可直接點開預覽，需要原稿請自助充值下載，所見才能所得，請見壓縮包內的文件及下方預覽，請細心查看有疑問可以咨詢QQ：11970985或197216396
Z3040型搖臂鉆床設計
摘 要:Z3040型搖臂鉆床屬于大型立式鉆床，其傳統的控制方式是利用繼電器接觸器原理控制。由于利用繼電器接觸器控制系統比較復雜，難于操作；因此本次設計是將其改造成為利用PLC控制，這樣既可以提高生產效率，也可以增加其使用壽命。
首先通過對鉆床工作原理的了解，然后對PLC的硬件和軟件進行設計。根據鉆床的工作要求選擇合理的工作器件如：繼電器，接觸器等等，然后編寫相應的程序語句表并繪制梯形圖，再根據輸入輸出點數選擇PLC型號，輸入點數：22輸出點數：17，所以本次設計選擇FX2N-48MR型PLC并繪制硬件接線圖；最后對程序進行模擬調試。
關鍵詞：PLC；電動機；行程開關；斷路器；控制按鈕；控制開關；工作指示燈。
Abstract: Z3040-arm drilling is a large vertical drilling, the traditional control method is the use of relay contacts Principle control. The use of the relay contactor control system more complicated and difficult operation, therefore this design is its use of a PLC control, this can enhance the efficiency of production and can also increase their service life.
By drilling the first principle of understanding, and then the PLC hardware and software design. According to drilling requirements for the work of the work of a reasonable choice of devices such as: relays, contacts, etc., and then the preparation of the corresponding procedures and the mapping of ladder diagram sentences table, the light input and output points choose PLC models, the importation of points: 22 output points: 17, Therefore, this design options FX2N-48MR PLC and the mapping of hardware wiring diagram; Finally, the simulation debugging procedures.
Key words: PLC; motor; trip switch circuit breaker; control button control switch; work light.
目 錄
第一章 引言·······························································1
第二章 機床的主要參數及鉆床的機械及運動形式···························2
第三章 繼電器接觸器控制原理·············································4
3.1制線路特點與電氣線路概述·········································4
3.2控制原理分析及分立控制線路·······································5
第四章PLC控制系統的硬件設計···········································10
4.1電動機的選型·······················································10
4.2接觸器的選擇·······················································12
4.3自動空氣斷路的選型················································15
4.4熱繼電器的選用·····················································16
4.5中間繼電器的選型···················································18
4.6萬能轉換開關的選型·················································18
4.7電磁鐵的選型·······················································19
4.8按鈕的選型··························································19
4.9位置開關的選型·····················································19
4.10導線的選型························································20
4.11變壓器的選型······················································20
4.12機床電氣控制系統的工藝設計······································23
4.13電氣元件布置圖的繪制·············································24
4.14電氣接線圖的繪制·················································25
4.15 可編程控制器·····················································26
4.16三菱PLC指令系統··················································35
第五章 PLC控制系統軟件設計··············································37
5.1輸入地址分配·······················································37
5.2輸出地址分配·······················································37
5.3接線圖······························································38
5.4程序語句表·························································39
第六章 程序模擬調試·······················································42第七章 總結·······························································44
致謝········································································45
參考文獻···································································46
VI