3803 軋輥車床PLC觸摸屏控制系統設計

3803 軋輥車床PLC觸摸屏控制系統設計,軋輥,車床,plc,觸摸屏,控制系統,設計 黑龍江工程學院本科生畢業設計I摘 要在國內軋輥制造行業使用的重型軋輥車床中,有許多是20世紀60年代和70年代制造的,目前仍作為軋輥加工的主要設備在服役。它們的主拖動普遍采用大功率直流電動機來實現,調速手段除少數延用F一D機組形式外,多數在20世紀80年代完成了第一步改造。利用PLC 控制單元驅動伺服電動機合理的無級調速范圍,代替原來純機械的有級變速,進而達到在不降低機械傳動性能的情況下,簡化機械傳動系統,改進機床操作性能。成功應用在重型軋輥車床上。本文介紹了觸摸屏PLC 控制系統在C84型軋輥車床上的應用，其中包括軋輥車床的組成、參數說明、控制系統構成及選型、扎輥車床的硬件接線、PLC輸入/輸出地址分配、觸摸屏畫面的組態、PLC梯形圖程序、指令表程序及PLC與觸摸屏的通信。通過對軋輥車床PLC 及觸摸屏的介紹，我們進一步熟悉了PLC與觸摸屏的設計方法及在工程應用中所要注意的問題。關鍵詞：軋輥車床；PLC；觸摸屏；梯形圖；組態黑龍江工程學院本科生畢業設計IIABSTRACTHeavy-duty roll lathe roll in the domestic manufacturing industry, many of which are manufactured in the 1960s and 1970s, is still as roll processing equipment in service. The main drag of commonly used high-power DC motor speed control means in addition to a few continue to use the F-D unit in the form, most completed in the 1980s the first step in the transformation. Stepless speed range of the PLC control unit to drive the servo motor instead of the original pure mechanical variable speed, and then reached in the case without reducing the performance of mechanical transmission, simplifying the mechanical drive system, improved the performance of the machine operator. Successfully applied in heavy-duty roll lathe.This article introduces a touch screen PLC control system in the bed of the C84-type roller vehicle, including the composition of the rolling roll lathe the parameter descriptions, control systems constitute and selection bar roll lathe of hardware terminal, the PLC input / output address allocated, touch-screen picture of theconfiguration, PLC ladder program instruction list program and the PLC and touch screen communication. The introduction of the roll lathe PLC and touch screen, we become more familiar with PLC and touch screen design and pay attention to problems in engineering applications.Key words: Roll lathe; PLC; touch screen; ladder ;Configuration