3183 摩托車尾燈罩注塑模具設計

3183 摩托車尾燈罩注塑模具設計,摩托,車尾,燈罩,注塑,模具設計 河南機電高等?？茖W(xué)校畢業設計/論文設計/論文題目： 摩托車尾燈罩注塑模班 級： 模具設計與制造 034 班姓 名： 郝 文 政 學號： 0 3 1 2 4 0 3 指導老師: 楊 占 堯 完成時間: 2006 年 5 月 摩托車尾燈罩注塑模設計摘要分析了摩托車尾燈罩的結構特點，介紹了該塑料件的注塑模具結構，以及該模具設計中澆注系統設計時面積比和流動比的校核方法。還介紹了此模具抽芯機構及復位機構的結構特點，以及在進行冷卻系統設計時確定冷卻水管數目的詳細計算過程及模具中部分零件的材料選用。該模具結構緊湊，合理經生產使用，各部分動作準確可靠，有效地解決了點澆口注射成型模成型薄壁制品常見的缺陷問題，塑件質量穩定，符合設計要求，可以實現大批量生產，而且生產效率高。關鍵詞：摩托車尾罩 注塑模具 澆注系統 抽芯機構 復位機構Design of the injection mould for the motorcycle light capAbstractThe structure characteristics of the plastic part is analyzed, the structure of the injection mould is introduced, asWell as the area ratio and 1iquid ratio calculate method in the pouring system of the mould design. The structure of pulling mechanism and resetting mechanism of the injection mould is also introduced as well as the determination of the quantity of cool water pipe and the material selection for the partial parts in the design of the cooling system.This mold structure compact, reasonably after production use, each part of movements accurate reliable, effectively solved a runner to inject the mold to take shape the thin wall product common flaw question, modelled a quality stably, conformed to the design requirement, might realize the mass production, moreover the production efficiency was high。Keywords： motorcycle light cap, injection mould, pouring system, pulling mechanism, insetting mechanism目錄緒論1 第一章 塑件工藝編程的編制41.1 塑件的工藝性分析 41.2 計算塑件的體積和質量51.3 塑件注塑工藝參數的確定6第二章 確定模具結構方案72.1 注塑模的結構設計72.1.1 分型面選擇72.1.2 確定型腔的排列方式82.1.3 澆注系統設計82.1.4 定模推出機構設計92.1.5 動模側向抽芯機構和推出機構設計 102.1.6 成型零件結構設計 11第三章 模具設計的有關計算123.1 型腔和型芯工作尺寸計算123.2 型腔側壁厚度和底板厚度計算 13第四章 模具加熱與冷卻系統的計算 154.1 求塑件在硬化時每小時釋放的熱量 Q15 4.2 求冷卻水的體積流量 V15第五章 模具閉合高度的確定16第六章 注塑機有關參數的校核16第七章 繪制模具總裝圖和非標零件工作圖17第八章 主要零件加工工藝規程18結 論20致 謝22參考文獻 23