汽車變速器設計【三軸式五擋手動變速器】

購買設計請充值后下載，資源目錄下的文件所見即所得，都可以點開預覽，資料完整，充值下載可得到資源目錄里的所有文件?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814 河南理工大學萬方科技學院本科畢業論文摘要變速器用來改變發動機傳到驅動輪上的轉矩和轉速，目的是在原地起步，爬坡，轉彎，加速等各種行駛工況下，使汽車獲得不同的牽引力和速度，同時使發動機在最有利工況范圍內工作。變速器設有空擋和倒擋。需要時變速器還有動力輸出功能。因?yàn)樽兯傧湓诘蜋n工作時作用有較大的力，所以一般變速箱的低檔都布置靠近軸的后支承處，然后按照從低檔到高檔順序布置各檔位齒輪。這樣做既能使軸有足夠大的剛性，又能保證裝配容易。變速箱整體結構剛性與軸和殼體的結構有關系。一般通過控制軸的長度即控制檔數，來保證變速箱有足夠的剛性。本文設計研究了三軸式五擋手動變速器，對變速器的工作原理做了闡述，變速器的各擋齒輪和軸做了詳細的設計計算，并進行了強度校核，對一些標準件進行了選型。變速器的傳動方案設計。簡單講述了變速器中各部件材料的選擇。關鍵字：擋數 傳動比 齒數 軸AbstractTransmission to change the engine reached on the driving wheel torque and speed, is aimed at marking start, climbing, turning, accelerate various driving conditions, the car was different traction and speed Meanwhile engine in the most favorable working conditions within the scope of the work. And the trans mission in neutral gear with reverse gear. Transmission also need power output function.Gearbox because of the low-grade work at a larger role, In general, the low-grade gearbox layout are close to the axis after support, Following from low-grade to high-grade order of the layout of stalls gear. This will not only allow axis are large enough for a rigid, but also ensures easy assembly. Gear box overall structure and rigid axle and the shell structure of relations. Generally through the control shaft length control over several stalls to ensure that adequate gear box rigid. This paper describes the design of three-axis five block manual trans mission, the transmission principle of work elaborated, Transmission of the gear shaft and do a detailed design, and the intensity of a school. For some standard parts for the selection. Transmission Trans mission program design. A brief description of the trans mission of all components of the material choice. Keywords : block; Transmission ratio; Teeth; Axis II