歡迎來到裝配圖網! | 幫助中心 裝配圖網zhuangpeitu.com!
裝配圖網
ImageVerifierCode 換一換
首頁 裝配圖網 > 資源分類 > DOC文檔下載  

外文翻譯--21世紀前半葉礦井提升機在深井中的應用

  • 資源ID:171440440       資源大?。?span id="z8pa56b" class="font-tahoma">250KB        全文頁數:14頁
  • 資源格式: DOC        下載積分:10積分
快捷下載 游客一鍵下載
會員登錄下載
微信登錄下載
三方登錄下載: 微信開放平臺登錄 支付寶登錄   QQ登錄   微博登錄  
二維碼
微信掃一掃登錄
下載資源需要10積分
郵箱/手機:
溫馨提示:
用戶名和密碼都是您填寫的郵箱或者手機號,方便查詢和重復下載(系統自動生成)
支付方式: 支付寶    微信支付   
驗證碼:   換一換

 
賬號:
密碼:
驗證碼:   換一換
  忘記密碼?
    
友情提示
2、PDF文件下載后,可能會被瀏覽器默認打開,此種情況可以點擊瀏覽器菜單,保存網頁到桌面,就可以正常下載了。
3、本站不支持迅雷下載,請使用電腦自帶的IE瀏覽器,或者360瀏覽器、谷歌瀏覽器下載即可。
4、本站資源下載后的文檔和圖紙-無水印,預覽文檔經過壓縮,下載后原文更清晰。
5、試題試卷類文檔,如果標題沒有明確說明有答案則都視為沒有答案,請知曉。

外文翻譯--21世紀前半葉礦井提升機在深井中的應用

英文原文Mine hoisting in deep shafts in the 1st half of 21st Century Alfred Carbogno 1 Key words: deep shaft, mine hosting, Blair winder, rope safety factor, drum sizing, skip factor Introduction The mineral deposits are exploited on deeper and deeper levels. In connection with this, definitions like “deep level” and “deep shaft” became more and more popular. These definitions concern the depth where special rules regarding an excavation driving, exploitation, rock pressure control, lining construction, ventilation, underground and vertical transport, work organization and economics apply. It has pointed out that the “deep level” is a very relative definition and should be used only with a reference to particular hydro-geological, mining and technical conditions in a mine or coal-field. It should be also strictly defined what area of “deep level” or “deep shaft” definitions are considered. It can be for example: - mining geo-engineering, - technology of excavation driving, - ventilation (temperature). It is obvious that the “deep level” defined from one point of view, not necessarily means a “deep level” in another area. According to 5 as a deep mine we can treat each mine if: - the depth is higher than 2300 m or - mineral deposit temperature is higher than 38 ºC. It is well known that the most of deep mines are in South Africa. Usually, they are gold or diamonds mines. Economic deposits of gold-bearing ore are known to exist at depths up to 5000 m in a number of South Africa regions. However, due to the depth and structure of the reef in some areas, previous methods of reaching deeper reefs using sub-vertical shaft systems would not be economically viable. Thus, the local mining industry is actively investigating new techniques for a single-lift shaft up to 3500 m deep in the near future and probably around 5000 m afterwards. When compared with the maximum length of wind currently in operation of 2500 m, it is apparent that some significant innovations will be required. The most important matter in the deep mine is the vertical transport and the mine hoisting used in the shaft. From the literature 1-12 results that B.M.R. (Blair Multi-Rope) hoist is preferred to be used in deep mines in South Africa. From the economic point of view, the most important factors are: - construction and parameters of winding ropes (safety factor, mainly), - mine hoisting drums capacity, This article of informative character presents shortly above-mentioned problems based on the literature data 1-12. Especially, the paper written by M.E. Greenway is very interesting 3. From two transport systems used in the deep shaft, sub-vertical and the single-lift shaft systems, the second one is currently preferred. (Fig.1.) 6 Hoisting Installation The friction hoist (up to 2100 m), single drum and the double drum (classic and Blair type double drum) hoist are used in deep shafts in South Africa. Drum winders Drum winders are most widely used in South Africa and probably in the world. Three types of winders fall into this category - Single drum winders, - Double drum winders, - Blair multi-rope winders (BMR). Double drum winders Two drums are used on a single shaft, with the ropes coiled in opposite directions with the conveyances balancing each other. One or both drums are clutched to the shaft enabling the relative shaft position of the conveyances to be changed and permitting the balanced hoisting from multiple levels The Blair Multi-Rope System (BMR) In 1957 Robert Blair introduced a system whereby the advantage of the drum winder could be extended to two or more ropes. The two-rope system developed incorporated a two-compartment drum with a rope per compartment and two ropes attached to a single conveyance. He also developed a rope tension-compensating pulley to be attached to the conveyance. The Department of Mines allowed the statutory factor of safety for hoisting minerals to be 4,275 instead of 4,5 provided the capacity factor in either rope did not fall below the statutory factor of 9. This necessitated the use of some form of compensation to ensure an equitable distribution of load between the two ropes. Because the pulley compensation is limited, Blair also developed a device to detect the miscalling on the drum, as this could cause the ropes to move at different speeds and so affect their load sharing capability. Fig.2 shows the depth payload characteristics of double drum, BMR and Koepe winders. The B.M.R. hoist is used almost exclusively in South Africa, probably because they were invented there, particularly for the deep shaft use. There is one installation in England. Because of this hoist's physical characteristics, and South African mining rules favouring it in one respect, they are used mostly for the deep shaft mineral hoisting. The drum diameters are smaller than that of an equivalent conventional hoist, so one advantage is that they are more easily taken underground for sub-shaft installations. A Blair hoist is essentially a conventional hoist with wider drums, each drum having a centre flange that enables it to coil two ropes attached to a skip via two headsheaves. The skip connection has a balance wheel, similar to a large multi-groove V-belt sheave, to allow moderate rope length changes during winding. The sheaves can raise or lower to equalize rope tensions. The Blair hoist's physical advantage is that the drum diameter can be smaller than usual and, with two ropes to handle the load, each rope can be much smaller. The government mining regulations permit a 5 % lower safety factor at the sheave for mineral hoisting with Blair hoists. This came about from a demonstration by the% permits the Blair hoists to go a little deeper than the other do. On the other hand, the mining regulations require a detaching hook above the cage for man hoisting. The balance wheel does not suit detaching hooks, so a rope-cutting device was invented to cut the ropes off for a severe overwind. This was tested successfully but the Blair is not used for man winding on a regular basis. The B.M.R. hoist has been built in three general styles similar to conventional hoists. The three styles are (Fig. 3 and 4): The gearless B.M.R. hoist at East Dreifontein looks similar to an in-line hoist except that the drums are joined mechanically and they are a little out of line with each other. This is because each drum directly faces its own sheaves for the best fleet angle. The two hoist motors are fed via thyristor rectifier/inverter units from a common 6.6-KV busbar. The motors are thus coupled electrically so that the skips in the shaft run in balance, similar to a conventional double-drum hoist. Each motor alternates its action as a DC generator or DC motor, either feeding in or taking out energy from the system. The gearless Blair can be recognized by the offset drums and the four brake units. A second brake is always a requirement, each drum must have two brakes, because the two drums have no mechanical connection to each other. Most recent large B.M.R. hoists are 4.27 or 4.57 m in diameter, with 44.5 ÷ 47.6 mm ropes 1. In arriving at a drum size the following parameters have been used: - The rope to be coiled in four layers, - The rope tread pressure at the maximum static tension to be less than 3,2 MPa, - The drum to rope diameter ratio (D/d) to be greater than 127 to allow for a rope speed of 20 m/s. With the above and a need to limit the axial length of the drums, a rope compartment of 8,5 m diameter by 2,8 m wide, was chosen. The use of 5 layers of coiled rope could reduce the rope compartment width to 2,15 m but this option has been discarded at this stage because of possible detrimental effects on the rope life. One problem often associated with twin rope drum hoists is the rope fleeting angle. The axial length of the twin rope compartment drums requires wide centres for the headgear sheaves and conveyances in the shaft. To limit the diameter of the shaft, the arrangement illustrated in Fig. 4 has been developed and used on a hoist still to be installed. Here, an universal coupling or Hookes Joint has been placed between the two drums to allow the drums to be inclined towards the shaft center and so alleviate rope fleeting angle problem, even with sheave wheels at closer centres 11. The rope safety factor The graphs in Fig. 5 illustrate the endload advantage with reducing static rope safety factors. While serving their purpose very well over the years, the static safety factor itself must now be questioned. Static safety factors, while specifically relating to the static load in the rope were in fact established to take account of: a. Dynamic rope loads applied during the normal winding cycle, particularly during loading, pull-away, acceleration, retardation and stopping, b. Dynamic rope loads during emergency braking, c. Rope deterioration in service particularly where this is of an unexpected or unforeseen nature. If peak loads on the rope can be reduced so that the peak remains equal to or less than that experienced by the rope when using current hoisting practices with normal static rope safety factor, the use of a reduced static rope safety factor can be justified. The true rope safety factor is not reduced at all. This is particularly of importance during emergency braking which normally imposes the highest dynamic load on the rope. Generally, the dynamic loads imposed during the skip loading, cyclic speed changes and tipping will be lower than for emergency braking but their reduction will of course improve the rope life at the reduced static rope safety factor. The means, justification and safeguards associated with a reduced static safety factor are discussed in 4,7,9,12. Based on the static rope safety factor of 4, the rope endload of 12843 kg per rope can be achieved. With twin ropes, this amounts to an endload of 25686 kg. With a conveyance based on 40 % of payload of 18347 kg with a conveyance of 7339 kg. There are hoisting ropes of steel wires strength up to Rm = 2300 MPa (Rm up to 2600 MPa 6 is foreseen) used in deep shafts. There are also uniform strength hoisting ropes projected 2,8. Conveyances The winding machines made from a light alloy are used in hoisting installations in deep shafts. The skip factor (S) has been defined as the ratio of empty mass of the skip (including ancillary equipment such as rope attachments, guide rollers, etc) to the payload mass. If the rope end load is kept constant, a lower skip factor implies a larger payload in other words, a more efficient skip from a functional point of view. However, the higher the payload for the same rope end load, the larger the out-of-balance load implying a more winder power going hand in hand with the higher hoisting capacity. If, on the other hand, the payload is fixed, a lower skip factor implies a lower end load and a smaller rope-breaking load requirement. Under these conditions, an out-of-balance load attributable to the payload would remain the same, but that due to the rope would reduce slightly. The sensitivity of depth of wind and hoisting capacity to skip the factor is illustrated in Fig. 6 and 7. A reduction of skip factor from 0,5 to 0,4 results in a depth gain of about 40 m for Blair winders and 50 m for single-rope winders. The increase of hoisting capacity for a reduction of skip factor by about 0,1 is about 10 %. Typical values for the “skip factor” are about 0,6 for skips and about 0,75 for cages for men and material hoisting. Reducing skip factors to say about 0,5 is a tough design brief and the trade-offs between lightweight skips and maintainability and reliability soon become evident in service. The weight can be readily reduced by omitting (or reducing in thickness) skip liner plates but this could reduce skip life by wear of structural plate leading to the high maintenance cost or more frequent maintenance to replace thinner liner plates. Similarly, if the structural mass is saved by reducing section sizes or changing the material from steel to aluminium for example, the structural reliability is generally reduced and the fatigue cracking becomes more efficient. Some success has been achieved in operating large capacity all aluminium skips with low skip factors but the capital cost is high and a very real hoisting capacity constrain must exist before the additional cost is warranted. It would appear that the depth and hoisting capacity improvements are better made by reducing the rope factor of safety and increasing the winding speed. The philosophy of the skip design should be to provide robust skips with reasonable skip factors in the range of 0,5 to 0,6 that can be hoisted safely and reliably at high speeds and that are tolerant to the shaft guide misalignment. It should be noted that some unconventional skips have been proposed (but not yet built and tested) that could offer skip factors as low as 0,35. Conclusions The first installation of Blaire hoists took place in 1958. From that time we can observe a continuous development of this double-rope, double-drum hoists. Currently, they are used up to the depth of 3 150 m (man/material hoist at the Moab Khotsong Mine, to hoist 13 500 kg in a single lift, at 19,2 m/sec, using 2 x 7400 kW AC cyclo-convertor fed induction motors). The Blair Multi-Rope system can be use either during shaft sinking or during exploitation. The depth range for them is 715 to 3150 m and the maximum skip load is 20 tons. In South Africa in deep shafts single lift systems are preferred. References 1 BAKER. T.J.: New South African Drum Hoisting Plants. CIM Bulletin, No 752, December 1994, p. 86-96. 2 CARBOGNO, A.: Winding Ropes of Uniform Strength. 1st International Conference LOADO 2001. Logistics and Transport. Hotel Permon, High Tatras, June 6th 8th 2001 p.214-217. 3 GREENWAY, M.E.: An Engineering Evaluation of the Limits to Hoisting from Great Depth. Int. Deep Mining Conference: Technical Challenges in Deep Level Mining, Johannesburg, SAIMM, 1990 p.449-481. 4 HECKER, G.F.K.: The Safety of Hoisting Ropes in Deep Mine Shafts. International Deep Mining Conference: Technical Challenges in Deep Level Mining. Johannesburg, SAIMM, 1990 p. 831-838. 5 HILL, F.G, MUDD J,B: Deep Level Mining in South African Gold Mines. 5th International mining Congress 1967, Moscow, p. 1 20. 6 LANE, N.M: Constraints on Deep-level Sinking an Engineering Point of View. The Certificated Engineer, vol. 62, No6, December 1989/January 1991 p. 3-9. 7 LAUBSCHER, P.S.: Rope Safety Factors for Drum Winders Implications of the Proposed Amendments to the Regulations. Gencor Group, 1995 Shaft Safety Workshop. Midrand, Johannesburg, November 1995, paper No 5 p.1-11. 8 MAC DONALD, D.H., PIENAAR, F.C.: State of the Art and Future Developments of Steel Wire Rope in Sinking and Permanent Winding Operations. Gencor Group, Shaft Safety Workshop Magaliesberg, 1994, paper No 13, p. 1-21. 9 MCKENZIE, I.D.: Steel Wire Hoisting Ropes for Deep Shafts. International Deep Mining Conference: Technical Challenges in Deep Level Mining. Johannesburg, SAIMM, 1990 p. 839-844. 10 SPARG, E.N.: Development of SA- Designed and Manufactured Mine Winders. The South African Mechanical Engineer vol.35, No 10, October 1985 p. 418-423. 11 SPARG E,N.: Developments in Hoist Design Technology Applied to a 4000 m Deep Shaft. Mining Technology, No 886, June 1995, p. 179-184. 12 SYKES, D.G., WIDLAKE, A.C.: Reducing Rope Factors of Safety for Winding in Deep Levels Shafts. International Deep Mining Conference. Technical Challenges in Deep Level Mining. Johannesburg, SAIMM, 1990 p. 819-829. 中文譯文21 世紀前半葉礦井提升機在深井中的應用關鍵詞: 深井,礦井提升機,布萊爾提升機, 鋼絲繩安全要素,滾筒尺寸, 驟變要素介紹礦物沉淀物在越來越深的水平上被開采。 關于這方面,像“深水平面”和“深井”的定義 變得越來越流行了。這些定義與有關特殊規則方面的深度有關,涉及到挖掘操縱 、開采、 巖石壓力控制、內層建造、通風,地下和垂直的運輸, 勞動組織和經濟學應用?!?深水平面 ”已經被指出是一種非常相對的定義,這個定義應當只能用于采礦或煤領域有關特殊的水-地質學, 采礦和技術條件方面的參考。 它也應當用于嚴格定義已經公認的有關“深水平面”或“深井”領域的定義。 可以舉例來說:- 采礦工程技術,- 開采操縱技術,- 通風 (降低溫度).明顯的是,從一方面得到的“深水平面”定義,在其他領域并不意味著“深水平面” 。 根據第5段提到的“深井”,我們可以設想每一個礦井:- 深度超過2300米深或者- 礦石沉積物的溫度超過38攝氏度。廣為人知的是大部分深井在南非。 通常,它們是金礦或者鉆石礦井。人們都知道像黃金方面礦石的經濟沉淀物存在于南非一些深達5000米的深井領域。 然而,在一些區域中,存在暗礁的深度和結構要素,先前在垂直的深井中使用的到達深度暗礁的方法在經濟上不可取。 因此,當?shù)氐牟傻V業正在積極地研究在不久的將來能夠用于深度達到3500米或者未來深度在5000米左右的礦井中的單一提升技術。相對于當今深度達2500米的礦井中的提升技術,它的一些創新在將來會有很大的意義。在深井中最重要的事件是垂直運輸以及礦井提升技術在井中的應用。參考文獻的1至12篇可以得出這樣的結論:布萊爾多繩提升機在南非的深井應用中是首選的。 從經濟學的觀點看, 最重要的要素是:- 提升繩索的構造和參數(主要是安全要素)- 礦井提升絞車的承載能力,這篇見聞廣博性質的文章簡略的介紹了上述基于參考文獻1至12篇所反映的問題。尤其, M.E. Greenway寫的文獻【3】非常有趣。從被應用于深井中的雙運輸系統,接近垂直的以及單一的井中提升系統,第二種系統是目前首選的。參見插圖1/參考文獻【6】。提升裝置摩擦提升機(提升深度達2100米),單獨的 和雙滾筒提升機(第一流的和布萊爾形式的雙滾筒提升機)廣泛應用于南非地區。1 Carbogno Alfred Ing 博士, 來自波蘭格利維策市西里西亞技術大學,采礦機械化學會, Akademicka 2 , PL 44-101 Gliwice, (他于2002年8月5日修訂了先前被公認為是標準的版本)滾筒提升機滾筒提升機被廣泛應用于南非或許全世界。 三種類型的提升機屬于這樣的類型:- 單一滾筒提升機,- 雙鼓提升機,- 布萊爾多繩繞線機 (BMR).雙滾筒提升機雙滾筒應用于單井,鋼絲繩以相對的方向纏繞在它的上面,以保持運輸工具的平衡。單一或者雙滾筒附著于井,使得運輸工具能夠在相對于井的位置上變換以及從不等高的水平面平穩的提升。布萊爾多繩系統 (BMR)在 1957 年,布萊爾羅伯特引進了一種提升系統,這種系統可以將滾筒的優勢擴大到能夠纏繞兩根或多根鋼絲繩。 這種雙繩系統發展成為二合一的滾筒,每一部分一根繩以及兩根繩附著在單一的運輸工具上。 他也開發了一種張緊滑輪裝置,把它附著在運輸工具上。 礦山部門說:倘若任何一根繩的承載能力要素不能降至法定要素9以下,將允許提升機械的法定安全要素從4275更改為45。這樣一種補償?shù)谋匾允沟锰幱趦筛K之間的載荷能夠平衡分配。因為滑輪的補償作用有限,布萊爾同樣發明了一種裝置來監測滾筒的誤差,因為這樣可以使得鋼絲繩能夠以不同的速度移動以及干預兩根繩能夠按他們的實際承載能力分配。 圖2描述了雙滾筒的深度有效載荷的特性,布萊爾和Koepe提升機。布萊爾提升機幾乎專一性的應用于南非地區,或許由于這些機器是在那兒發明的,尤其是應用于深井。 在英國有一套設備。 因為這種提升機的物理性能好,以及南非地區的礦井規程在某一方面特別親賴于它,他們主要被應用于深井提升系統。這種滾筒的直徑比普通相當規格的提升機小,因此一方面的優點是它們更加便于在井下安裝。布萊爾提升機本質上是帶有寬鼓的常規提升機,每個滾筒有一個中心凸輪,以使得兩根繩子能夠纏繞在上面,用來急速改變兩個主導輪。 急變系統擁有一個平衡輪, 類似于大的多凹槽形的V帶滑輪, 以允許在提升過程中繩索長度的適度變化?;喣苌鸹蛘呓档鸵允沟娩摻z繩的張緊力相等。布萊爾提升機的物理性能優勢表現在滾筒的直徑比普通的小,以及兩根繩子同時承載載荷,使得每根繩子能夠變得更加小些。政府部門的采礦規則允許使用布萊爾提升機的礦井在滑輪安全要素方面低于正常5。這從發明家羅勃特布萊爾的演示可以看出, 一根嚴格符合要求的鋼絲繩,以額定速度運轉, 由剩余的鋼絲繩承擔負載。 這 5% 的安全要素允許布萊爾提升機比其他提升機稍微深入一些。 另一方面, 采礦規則要求為方便人們的升降,在罐籠的上方必須安裝有可分離的吊鉤。 平衡輪不適合用于分離吊鉤,因此,發明了一種可以切斷繩索的裝置用來切斷旋得很緊的繩索。 這種裝置順利通過試驗,但是布萊爾提升機不是用于人類規范準則的提升機。布萊爾提升機已經被應用于三種類似于傳統提升機的普通風格的類型中。 這三種風格可見圖 3 和圖 4。在Dreifontein東部的無傳動裝置的 B.M.R. 提升機除滾筒連接以及它們相互不在同一中心外,從外表上看似同軸提升機。這是因為每個滾筒直接地面對自己的滑槽輪而獲得最佳的深淺角度。 兩個提升機的馬達通過6.6千伏的半導體閘流管整流換流器/反用換流器來反饋。馬達與電相連接以便軸中的急變能夠保持平衡,類似于傳統的雙滾筒提升機。每臺馬達交替變換它們的作用相當于直流發電機或者直流電動機任意的從系統中輸入或者輸出能量。無傳動裝置的布萊爾提升機能夠被偏移滾筒和四種剎車裝置所檢驗。 第二種剎車永遠是必要的,每個滾筒必須有兩個剎車,因為兩個滾筒之間沒有機械連接。大部分最新的布萊爾提升機直徑達到4.27或者4.57米,附帶有直徑達44.5至47.6毫米的鋼絲繩。在達到滾筒的尺寸方面,以下的參數已經被采用:- 鋼絲繩被纏繞成四層,- 鋼絲繩的最大靜態壓力要小于32兆帕,- 滾筒與鋼絲繩的直徑比(大徑比小徑)要大于127,以保證鋼絲繩的速度達到20米/秒。綜上所述為限制滾筒的軸的長度的需要,鋼絲繩減速箱的尺寸選擇為直徑85米、寬28米。 5層纏繞的鋼絲繩的利用可以使鋼絲繩間隔間的寬度減少到215米,但是這種想法在此階段已經被放棄,是因為它們可能對鋼絲繩的壽命有負面影響。經常與雙繩滾筒提升機有關的一個問題是鋼絲繩的短暫角度.雙繩間隔間滾筒的軸長為了提升機能夠在礦井中順利的運輸,需要寬敞的中心區。為了限制井的直徑,在圖4中安排的插圖直到提升機被安裝才被證實是正確的。這里,通用的或者Hooke的結合點已經在雙滾筒之間安置,這是為了允許滾筒在礦井中心被連接以及能夠減小鋼絲繩的角度問題,以及槽輪在靠近的中心問題。鋼絲繩的安全要素在圖5中的圖表舉例說明了鋼絲繩在減少靜態安全要素方面的負載優勢。 當數年以來很好的滿足它們的目的,靜態安全要素現在本身一定會被質疑的。 靜態安全要素,雖然在鋼絲繩上與靜態負載有明確的關聯,事實上已經有了明確的考慮:a、 動態的繩索負載應用于正常的纏繞循環周期中,尤其在加載、離開、加速、延遲以及停止,b、 動態繩索負載在緊急制動中,c、 工作期間的繩索變化尤其處于以外的或者無法預料的狀態。如果鋼絲繩的最大負載能夠減少以便最大負載殘余應力能夠平擔或者少于曾經承受過的負載,當使用的當前的提升實際能力以及普通的靜態繩索安全要素,靜態繩索安全要素降低的利用被證實是正確的。真正的繩索安全要素實質上并沒有減少。這在鋼絲繩處于最大動態負載的緊急制動中尤其重要。通常,在負載急變瞬間的動態加載, 循環的速度變化將會緊急制動的情況,但是它們的減少一定會在減少的靜態繩索安全要素方面改善鋼絲繩的壽命。那些與降低的靜態安全要素相關的合理的以及安全的手段在參考書4,7,9,12中有相關的討論。基于第四篇文獻中涉及的靜態繩索安全要素,每一根鋼絲繩所能承受的最大負載為12843千克。對于雙繩來說,最大負載量達到25686千克?;?8347千克的運輸量的40的有效載荷為7339千克。在深井中提升鋼絲繩的力量最大可以達到2300兆帕(在第六篇參考文獻中所估計的可以達到2600兆帕)。在第2,8篇參考文獻中提到的提升機鋼絲繩被設計成統一的額定載荷。運輸纏繞機器由閃光合金制成廣泛使用于深井提升設備中。急變要素作為空載對有效載荷的比例已經被詳細的論述(包括輔助設備,例如鋼絲繩附加裝置、引導滾筒等等)。如果鋼絲繩的最大載荷保持不變,一種低級的急變要素暗示著有更大的有效載荷,換句話說,是來自于功能觀點的更有效率的急變特征。然而,同一鋼絲繩的有效最大載荷越高,來自平衡的載荷越大,意味著與提升高能量相關的纏繞能量越來越高。另一方面,如果有效載荷被確定,更低的急變要素意味著更低的最大負載以及更小的繩索制動加載設備。在這些條件下,來自于平衡外的負載雖然仍然歸于有效載荷,但是應歸于繩索的少量降低。在圖6、7中描述了纏繞和提升機容量的深度靈敏性。急變要素從0.5降低到0.4,導致布萊爾提升機深度增加大約40米,單繩提升機增加大約50米。急變要素降低了0.1使得提升機容量大約增加了10。急變要素的典型價值體現在人和材料提升運輸方面,急變方面為0.6,罐籠方面為0.75。在工作中輕量級以及可維護性和可靠性迅速變得明顯之間,急變要素的降低被認為與0.5有關,其實是一種很難的規劃設計。重量可以很容易的通過省略(或者在厚度方面減少)急變襯墊金屬板 ,但是這種方法可

注意事項

本文(外文翻譯--21世紀前半葉礦井提升機在深井中的應用)為本站會員(紅**)主動上傳,裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對上載內容本身不做任何修改或編輯。 若此文所含內容侵犯了您的版權或隱私,請立即通知裝配圖網(點擊聯系客服),我們立即給予刪除!

溫馨提示:如果因為網速或其他原因下載失敗請重新下載,重復下載不扣分。




關于我們 - 網站聲明 - 網站地圖 - 資源地圖 - 友情鏈接 - 網站客服 - 聯系我們

copyright@ 2023-2025  zhuangpeitu.com 裝配圖網版權所有   聯系電話:18123376007

備案號:ICP2024067431-1 川公網安備51140202000466號


本站為文檔C2C交易模式,即用戶上傳的文檔直接被用戶下載,本站只是中間服務平臺,本站所有文檔下載所得的收益歸上傳人(含作者)所有。裝配圖網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對上載內容本身不做任何修改或編輯。若文檔所含內容侵犯了您的版權或隱私,請立即通知裝配圖網,我們立即給予刪除!