《生產螺絲時,螺絲線徑對應表》由會員分享，可在線閱讀，更多相關《生產螺絲時,螺絲線徑對應表（5頁珍藏版）》請?jiān)谘b配圖網上搜索。
1、深圳創固螺絲 生產螺絲時，螺絲線徑對應表。我們在生產制造 螺絲時，首先當然是確實用什么螺絲材料， 然后在根據螺絲規格大小，要采用與之相對應的螺絲線材線徑大 小。有些螺絲線徑大的，我們可以拿去拉絲，把螺絲線徑大的拉小 一點，拉成我們所需要的螺絲線材。 但如果有現有的，我們也可以 買現有的螺絲線徑，直接用來生產制造螺絲。下面把生產螺絲與之對應的徑線表展示一下，供大家參考：機械螺絲線徑表機械螺絲IFIDIN般機械牙般機械牙JIS規格線徑規格線徑規格線徑2-561.83M1.0M1.00.833-482.11M1.2M1.21.054-402.35M1.4M1.41.195-402.70M1.7M1.
2、71.406-322.91M2.01.65M2.01.658-323.56M2.52.15M2.21.9710-244.05M3.02.57M2.31.972-641.87M3.53.01M2.52.233-562.15M4.03.45M2.62.234-482.43M4.54.35M3.02.575-442.73M5.05.22M3.53.026-403.02M4.03.458-363.63M4.53.9210-324.22M5.04.35M6.05.25鐵板螺絲線徑表木螺絲40度牙IFIDIN規格線徑規格線徑規格線徑規格#21.65M3.02.25M3.02.11M1.0#42.25M3.
3、52.78M3.52.45M1.2#52.50M4.03.05M4.02.78M1.4#62.78M4.53.45M4.53.11M1.6#73.05M5.03.81M5.03.45M1.7#83.28M2.0#103.73M2.3M2.5M2.6木螺絲線徑表STCTBTPT線徑線徑線徑線徑0.860.730.811.060.941.001.221.091.201.391.291.311.491.431.421.771.711.691.622.062.001.911.892.242.162.082.012.342.262.182.14三角牙鐵板螺絲DINIFIJISAB,BZ,IFI / BZ
4、EJ牙A牙A牙AB牙規格線徑線徑線徑規格線徑線徑M1.0M1.00.830.80M1.20.96M1.21.02M1.41.151.05M1.41.151.15M1.71.40M1.71.401.40M2.2(2.0)1.751.651.75M2.01.701.65M2.6(2.5)2.051.802.05M2.31.951.85M2.9(3.0)2.252.152.25M2.62.152.10M3.32.602.60M3.02.402.40M3.52.782.462.78M3.52.802.80M3.9(4.0)3.112.903.11M4.03.253.25M4.23.333.28M4.53.553.55M4.83.813.73M5.03.904.05M5.0M3.02.732.632.492.45M3.53.153.052.922.89M4.03.583.483.303.25M4.54.073.943.743.65M5.04.544.404.184.05
生產螺絲時,螺絲線徑對應表
