沖床上下料機械手設計【液壓驅動 三自由度圓柱坐標式】【7張CAD圖紙+PDF圖】

喜歡就充值下載吧。資源目錄里展示的文件全都有，請放心下載，有疑問咨詢QQ:414951605或者1304139763 = 喜歡就充值下載吧。資源目錄里展示的文件全都有，請放心下載，有疑問咨詢QQ:414951605或者1304139763 = 摘 要本論文主要介紹了沖床上下料機械手的設計過程。在查閱了一系列參考資料以后，參閱國內的設計情況。選用圓柱座標和三自由度。機械手的各執行機構，包括:手部、手臂等部。用氣流負壓式吸盤來吸取板料工件。在分析了具體工作要求，對個方案進行對比之后，綜合考慮各個因素。機械手腰部的旋轉運動需要一定的定位控制精度，故采用步進電機驅動來實現；因?yàn)椴捎靡簤簣?zhí)行缸來做水平手臂和垂直手臂，故大小臂均采用液壓驅動；機械手的手部結構設計，因?yàn)楣ぜ前辶?，使用氣流?fù)壓式吸盤.采用氣動驅動。關鍵詞：沖床 機械手 負壓吸盤AbstractThe present paper mainly introduced on the punch press the yummy treats manipulators design process. After having consulted a series of reference, refers to the domestic design situation. Selects the circular cylindrical coordinate and three degrees-of-freedom. Manipulators each implementing agency, including: Hand, arm and so on. Absorbs the sheet work piece with the air current negative pressure type sucker. In has analyzed the concrete work requirement, carries on the contrast after a plan, overall evaluation each factor. The manipulator waists rotary motion needs certain positioning control precision, therefore uses step-by-steps the motor-driven to realize; Because uses the hydraulic pressure execution cylinder to make the horizontal arm and the vertical arm, therefore the big and small arm uses the hydraulic pressure actuation; Manipulators hand structural design, because the work piece is the sheet, use air current negative pressure type sucker. Uses the air-operated drive. key words: Punch press manipulator negative pressure sucker 目 錄摘要.IABSTRACT.II緒論11 機械手概述21.1 機械手的組成22 機械手的總體設計42.1.1 機械手總體結構的類型.42.1.2 設計具體采用方案52.2 機械手腰座結構的設計62.2.1 機械手腰座設計的具體采用方案.72.3 機械手手臂的結構設計72.3.1 設計具體采用方案 .82.4 機械手的手部結構方案設計92.5 機械手的機械傳動機構的設計92.6 設計具體采用方案122.7機械手驅動系統的設計122.7.1設計具體采用方案.193 理論分析和設計計算193.1液壓傳動系統設計計算193.1.2擬定液壓執行元件運動控制回路. .213.1.3確定液壓系統的主要參數.223.1.3.液壓缸主要參數的確定.233.1.4計算和選擇液壓元件.253.2電機選型和有關計算273.2.1有關參數的計算273.2.2電機型號的選擇283.3吸盤部件的選擇和計算303.3.1真空發生器選定及吸著響應時間計算323.3.2其它氣動元件選定34結論35參考文獻36致謝.37