帶聯合頂出機構的注射模的設計【一模二腔】【說明書+CAD】

購買設計請充值后下載，資源目錄下的文件所見即所得，都可以點開預覽，資料完整，充值下載可得到資源目錄里的所有文件?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814 畢業設計(論文)外文資料翻譯系部： 機械工程系 專 業： 機械設計及自動化 姓 名： 學 號： 0 外文出處：Proceedings of the 61rd Annual Technical Conference 2003 附 件： 1.外文資料翻譯譯文；2.外文原文。指導教師評語：外文翻譯基本正確，能達到本科畢業的水平。基本上能準確地表達原文思想，語句較為通順，條理清楚，基本符合中文習慣，整體翻譯質量較好。 簽名： 年 月 日附件1：外文資料翻譯譯文普通全鋼沖模的沖壓精度分析板料沖壓件的精度準確顯示出其沖模的沖壓精度。而任何沖件的線性尺寸精度與形位精度主要取決于沖模沖裁和立體成形沖壓件展開平毛坯的落料精度。因此，多工步復合沖壓的單工位復合模、多工位連續模的沖壓精度，在普通沖壓的眾多種類與不同結構的沖模中，最具典型性和代表性。沖模的沖壓精度分析對沖模投產至失效報廢各個時期沖件的實際誤差分析，可以看出其增大的時期及趨向，從而分析其增大的因素。新沖模投產至第一次刃磨前沖制沖件的誤差即所謂的初始誤差；沖模經過20次左右刃磨至失效報廢前沖制的沖件誤差稱之為常規誤差；而沖模失效報廢前沖制的最后一批合格沖件的允許最大誤差稱之為極限誤差。在現場，確定沖模刃磨壽命的依據是沖件沖孔與落料的毛刺高度。由于任何成形件都具有沖裁作業（毛坯落料或沖孔），對于復合模尤為如此。所以，沖件毛刺高度的觸模檢查和測量并按企業標準或JB4129-85沖壓件毛刺高度對照檢測就顯得十分重要。沖模的初始誤差通常是沖模整個壽命中沖件誤差最小的。其大小主要取決于沖模的制造精度與質量及沖件尺寸、料厚以及間隙值大小與均勻度。沖模的制造精度及質量又取決于制模工藝。對于料厚t1mm的中碳鋼復合沖裁模沖件，實驗結果與生產實踐都證明，電火花線切割制造的沖模沖件毛刺高度比用成型磨或NC與CNC連續軌跡座標磨即精密磨削工藝制造的沖模沖件要高25%30%。這是因?yàn)楹笳卟粌H加工精度高，而且加工面粗糙度Ra值要比前者小一個數量級，可達到0.025m。因此，沖模的制造精度與質量等因素決定了沖模的初始沖壓精度，也造就了沖件的初始誤差。沖件的常規誤差是沖模經第一次刃磨到最后一次刃磨后沖出最后一個合格沖件為止，沖件實際具有的誤差。隨著刃磨次數的增加，刃口的自然磨損而造成的尺寸增量逐漸加大，沖件的誤差也隨之加大。當其誤差超過極限偏差時，沖件就不合格，沖模也就失效報廢。沖件上孔與內形因凸模磨損尺寸會逐漸變小；其外形落料尺寸會因凹模磨損而逐漸增大。所以，沖件上孔與內形按單向正偏差標允差并依接近或幾乎等于極限最大尺寸制模。同理，沖件外形落料按單向負偏差標注允差并依接近或幾乎等于極限最小尺寸制模。這樣就使沖件的常規誤差范圍擴大，沖模可刃磨次數增加，模具壽命提高。沖件的極限誤差是具有極限偏差的沖件所具有的實際允許的最大尺寸誤差。這類沖件通常是在沖模失效報廢前沖制的最后一批合格沖件。對各類沖模沖件誤差在沖模整個壽命中出現的波動、增減趨向及規律等進行全面分析便可發現：沖件誤差的主導部分是不變的；因刃口或型腔的自然磨損而出現的誤差增量隨沖模刃磨沖數增加而使這部分誤差逐漸加大；還有部分誤差的增量是非常規的、不可預見的。所以，各類沖模沖件誤差是由因定誤差、漸增誤差、系統誤差及偶發誤差等幾部分綜合構成。1、因定誤差新沖模在指定的沖壓設備上投入使用至失效報廢的整個（總）壽命過程中，其合格沖件誤差的主導部分固定不變即所謂固定誤差。其大小就是新沖模第一次刃磨前沖制的合格沖件的偏差，也即沖模的初始誤差，而此時的沖模具有初始沖壓精度。刃磨后的沖模，因其工作零件（凸、凹模）磨損而改變尺寸誤差，使沖件識差增量隨刃磨次數增加而逐漸加大，故沖模刃磨后的沖壓精度亦稱“刃磨精度”比其初始精度要低。沖模沖件的固定誤差取決于以下各要素：（1）沖件的材料種類、結構（形狀）尺寸及料厚沖裁間隙的大小及其均勻度對沖裁件的尺寸精度有決定性的影響。不同沖裁工藝、不同材料種類與不等料厚，間隙相差懸殊，沖壓精度差異很大。同一種模數m=0.34的2mm的料厚、中心有孔的H62黃銅材料片齒輪復合模沖件，當取間隙C=0.5%t（單邊），用復合精沖模沖制，沖件尺寸精度達到IT7級，沖件平直無拱彎，沖切面垂直度可達89.5，其表面粗糙Ra值為0.2m；而用普通復合模沖制，間隙C=5%t（單邊），沖件初始誤差亦即沖模的初始沖壓精度為1T9級，沖切面粗糙度Ra值為12.5m，毛刺高度為0.10mm；還是這個沖件用連續模沖制，間隙C=7%t（單邊），初始沖件精度為IT11級，沖切面更粗糙，甚至有肉眼可見的臺階。通常情況下，沖件材料及其厚度t是選取沖裁間隙的主要依據。一旦選定間隙就確定了沖件的平面尺寸的固定誤差的主體；沖件結構剛度及立體形狀則影響其形位精度。（2）沖壓工藝及沖模結構類型采用不同的沖壓工藝，沖件的精度及固定誤差相差甚大。除上述片齒輪實例說明，精沖工藝與普通沖裁的沖件精度與固定誤差相差一個數量級之外，即便在普通沖裁中，采用不同間隙沖裁，固定誤差相差也很大。例如料厚t=1.5mm的H62黃銅沖裁件，選用C40%t單邊類小間隙沖裁比選用C8%t（單邊）類大間隙沖裁，沖件固定誤差將加大40%60%，精度至少降一級。此外，采有無搭邊排樣，沖件的誤差要遠大于有搭邊排樣沖件。無搭邊排樣沖件。無搭邊排樣沖件的精度低于IT12級，而多數有搭邊排樣的沖件精度在IT11IT9級之間，料厚t4mm的沖件，尺寸精度會更低一些。不同沖模結構類型，由于適用沖壓料厚及制造精度的差異，導致沖件的固定誤差有別。復合模中，多工位連續式復合模由于沖件連續重復定位加上制模誤差較大，故其沖件的固定誤差比單工位復合沖裁模要 大12級。（3）沖模制造工藝沖模主要工作零件即凸、凹模的加工程序，對操作上的技術要求不高，能夠一次成形較復雜的模腔。但其加工表面約厚0.030.05mm為高溫?zé)g的殘余樹枝狀?yuàn)W氏體組織，硬度可高達HRC6770，有顯微裂紋，容易在沖裁時出現崩刃或剝落。意大利Corrada公司的有關研究報告稱“線切割加工對表面金相結構產生不利的影響，實際上已經改變了金相結構。我們必須用金剛石粉研磨或數控連續軌跡坐標磨削（對線切割件）作精加工”。近年來瑞士和日本等國，對電加工設備進行了深入的研究和較大的改進，制造出功能齊全的高精度NC和CNC線切割機，加工精度可達0.0050.001mm，甚至更小。加工表面粗糙度Ra值能達到0.4m。根據近年對國內12家生產線切割機工廠的調研，國產線切割機加工精度各別廠家的各別型號線切割機可達0.0080.005mm，一般都在0.01mm或更大一些，個別也能達到0.005mm，加工表面粗糙度Ra值均大于1.6m。然而，電加工燒蝕金屬表面從而改變和損壞加工面金相結構的特性不會改變，除非用磨削或其他加工法去除這一有害層。所以，僅僅用電加工法，包括電火花線切割與電穿孔，難以達到?jīng)_模，尤其高精度、高壽命沖模對尺寸精度與工作零件表面粗糙度Ra值要求。用精密磨削法制造沖模，特別是制造高精度、高壽命沖模，諸如：薄料小間隙復合沖裁模、多工位連續式復合模等，具有尺寸精度高、工作零件加工面粗糙度Ra值小、模具壽命高等特點。其加工工藝目前已由過去的普通機床粗加工改為電火花線切割或電穿孔機粗加工，最后精密磨削，也由成型磨、光學曲線磨、手動座標磨逐步過濾到連續軌跡座標磨及NC與CNC連續軌跡座標磨，加工粗度可達0.0010.0005mm，加工表面粗糙度Ra值可達0.10.025m。所以，用該工藝制造的沖模，無論尺寸精度、工作零件表面粗糙度，都能滿足沖模，尤其各種復合模的要求，比電加工工藝制造的沖模高一個檔次。（4）間隙的大小與均勻度拉深、彎曲、翻邊及其他板料成形件一般都要先沖裁（落料）出平板展開毛坯，也有成形后落料、切開得到單個成品沖件。故沖裁作業，包括常用的沖孔、切口、切邊等，對于每種板料沖壓件都是必要的。所以沖裁間隙對沖件的外廓尺寸精度有決定性的影響。沖裁間隙小而均勻，可使沖裁尺寸獲取更高精度。對于拉深、彎曲等成形模，間隙大定將增大沖件口部尺寸誤差及回彈。間隙不均勻會使沖件毛刺加大并招致刃口的不均勻磨損。（5）沖壓設備的彈性變形在沖壓過程中，沖床承載后會產生一定的彈性變形。雖然這種變形量依沖壓力的大小變化且具有明顯的方向性，但就沖壓件，主要是對具有體積沖壓性質的壓印、壓花、校平、壓凸、起波、沖擠、鐓形、翻邊、鐓粗、打扁、變薄拉深等工藝作業沖制成形的沖件，對其沖壓方面的尺寸精度有重大影響。附件2：外文原文General all-steel punching dies punching accuracyAccuracy of panel punching part is display the press accuracy of the die exactly. But the accuracy of any punching parts linear dimension and positional accuracy almost depend on the blanking and blanking accuracy ,. So that the compound mould of compound punchings accuracy, is typicalness and representation in the majority.Analyse of the dies accuracy For the analyse of pracyicable inaccuracy during production of dies to inactivation, we could get the tendency when it is augmentation in most time. From this we could analyse the elements . when the new punch dies pt into production to the first cutter grinding, the inaccuracy produced called initial error ; if the die grinding more than twenty times , until its discard, the inaccuracy called conventional error ; and before the dies discard, the largest error of the last batch permit , called limiting error. at job site, the evidence to confirm life of sharpening is the higher of the blanking, punched hole or punched parts. Because all finished parts had been blanked ,so it is especially for the compound dies. Therefore, the analyse of burr and measurement is especially important when do them as enterprise standardization or checked with .The initial error usually is the minimal through the whole life of die. Its magnitude depend on the accuracy of manufacture, quality, measure of the punching part, thickness of panel, magnitude of gap and degree of homogeneity. The accuracy of manufacture depend on the manufacture process. For the 1 mm thicked compound punching part made in medium steel, the experimental result and productive practice all prove that the burr of dies which produced by spark cutting are higher 25%30% than produced by grinder ,NC or CNC. The reason is that not only the latter have more exact machining accuracy but also the value of roughness Ra is less one order than the formmer , it can be reached 0.025m. The normal error of the punch die is the practicable error when the fist cutter grinding and the last cutter grinding before the die produce the last qualified product. As the increase of cutter grinding, caused the measure the nature wear of the dies are gradual increasing, the error of punching part increase also, so the parts are blew proof. And the die will be unused. The hole on the part and inner because the measure of wear will be small and small gradually, and its outside form will be lager in the same reason. Therefore, the hole and inner form in the part will be made mould according to one-way positive deviation or nearly equal to the limit max measure. In like manner, the punching parts appearance will be made mould according to one-way negative deviation or nearly equal to limit mini measure. For this will be broaden the normal error, and the cutter grinding times will be increased, the life will be long.The limit error in punching parts are the max dimension error which practicable allowed in the parts with limit error. This kind of parts usually are the last qualified products before the die discard. For the all classes of dies, if we analyse the fluctuate, tendency of increase and decrease and law which appeared in the dies whole life, we will find that the master of the error are changeless; the error that because the abrade of the cutter and impression will be as the cutter grinding times increased at the same time. And that will cause the error oversize gradually; and also have another part error are unconventional , unforeseen. Therefore, every die s error are composed of fixed error, system error, accident error and so on. 1. fixed error At the whole process when the New punching die between just input production to discard, the changeless master error that in qualified part are called fixed error. Its magnitude is the deviation when the die production qualified products before the first cutter grinding. Also is the initial error, but the die have initial punching accuracy at this time. Because of the abrade of parts, the die after grinding will be change the dimension error. And the increment of deviation will oversize as the times of cutter grinding. So the punching accuracy after cutter grinding also called “grinding accuracy” and lower tan initial accuracy. The fixed error depend on the elements factor as followed :(1) the material , sorts, structure, (form) dimension, and thick of panel the magnitude of punching gap and degree of homogeneity are have a important effect for the dimension accuracy. Different punching process, material, thick of panel, have completely different gap and punching accuracy. A gear H62 which made in yellow brass with the same mode number m=0.34, 2mm thick and had a center hole, when the gap get C=0.5%t (single edge) , and punched with compound punching die, and the dimension accuracy reached IT7, the part have a flat surface ,the verticality of tangent plane reached 89.5, its roughness Ra magnitude are 12.5m, height of burr are 0.10mm; and the punching part are punched with progressive die, the gap C=7%t (single edge) , initial accuracy are IT11, and have an more rough surface, even can see the gap with eyes. In the usual situation, flushes a material and its thickness t is theselection punching gap main basis. Once the designation gap haddetermined flushes the plane size the fixed error main body; Flushesthe structure rigidity and the three-dimensional shape affects itsshape position precision.(2) punching craft and molder structure type Uses the different ramming craft, flushes a precision and the fixederror difference is really big. Except that the above piece gearexample showed, the essence flushes the craft and ordinary punching flushes a precision and the fixed error differs outside a magnitude,even if in ordinary punching center, uses the different gap punching, thefixed error difference very is also big. For example material thickt=1.5mm H62 brass punching, selects C = the 40%t unilateral I kind ofsmall gap punching compared to select C 4mm flushes, the size precision can lower some. Different dies structure type, because is suitable the rammingmaterial to be thick and the manufacture precision difference, causesto flush a fixed error to have leaves. Compound die center, multi-locations continuous type compound die because flushes continuously toduplicate the localization to add on the pattern making error to bebigger, therefore it flushes a fixed error compound punching die to wantcompared to the single location Big 1 2 levels(3) the craft of punching dies manufacturethe main work of punching die namely are raised, the concave moldprocessing procedure, to operates on the specification not to behigh, can time form a more complex cavity. But its processing surfaceapproximately is thick 0.03 0.05mm is the high temperatureablation remaining furcated austenite organization, degree ofhardness may reach as high as HRC67 70, has the micro crack, easilywhen punching appears broke the cutter or flaking. The Italian CorradaCorporations related memoir called the line cut the processing contruction to have the disadvantageous influence to the superficialgold, in fact already changed the gold contruction. We must use theJingang stone powder to grind or the numerical control continual pathcoordinates rub truncate (cut to line) to make the precision work . In recent years country and so on Switzerland and Japan, has conductedthe thorough research to the electrical finishing equipment and abigger improvement, makes function complete high accuracy NC and theCNC line cutter, the processing precision may reach 0.005 0.001mm,even is smaller. The processing surface roughness Ra value can achieve0.4 mu m. According to the recent years to the domestic 12 productionlines cutter factory investigation and study, the domesticallyproduced line cutter processing precision different factory differentmodel line cutter might reach 0.008 0.005mm, generally all in0.01mm or bigger somewhat, was individual also can achieve0.005mm, the processing surface roughness Ra value was bigger than1.6m. However, the electrical finishing ablation metal surface thus the change and the damage machined surface mental structure character can not change, only if with rubs truncates or other ways removes this harmful level. Therefore, merely uses electricity machining, including the spark cutting and the electricity perforation, achieves with difficulty punching, especially high accuracy, high life punching die to size precision and work components surface roughness Ra value request. With precisely rubs truncates the law manufacture punching die, specially makes the high accuracy, the high life punching die, such as: Thin material small gap compound punching die, multi- locations continuous type compound die and so on, has the size precision high, the work component smachined surface roughness Ra value is small, the mold life higher characteristic. Its processing craft at present changed the electrical fire by the past ordinary engine bed rough machining spark cutting or the electricity puncher rough machining, finally precisely rubs truncates, also from takes shape rubs, optics curve rubs, the manual grid reference rubs gradually filters the continual path grid reference to rub and NC and the CNC continual path grid reference rubs, Processing coarseness may reach 0.001 0.0005mm, the processing surface roughness Ra value may reach 0.1 0.025 mu m. Therefore, with this craft manufacture the die , regardless of the size precision, the work components surface roughness, all can satisfy die, each kind of compound request, the die is especially higher than the electrical finishing craft manufacture scale.(4) gap size and degree of homogeneity the flange and other sheet forming sgene rally all must first punching (fall material) the plate to launch the semi finished materials, after also has the forming to fall the material, the incision obtains the single end product to flush. Therefore punching the work, including is commonly used punching hole, the margin, cut side and so on, regarding each kind of sheet pressing partall is necessary. Therefore punching the gap to flushes a out form in chprecision to have the decisive influence. punching the gap small and is even, may cause punching the size gain high accuracy. Regarding drawability, is curving and so on mould, the gap greatly will decide increases flushes the oral area size error and the snapping back. The gapnon-uniformity can cause to flush a burr enlarges and incurs cutting edge the non-uniform attrition. (5) ramming equipment elastic deformation In the ramming process after the punch press load bearing can have the certain elastic deformation. Although this kind of distortion quantity according to flushes the pressure the size to change also tohave the obvious directivity, but on the pressing part, mainly is tohas the volume ramming archery target stamping, embosses, thee qualization, the pressure is raised, the wave, flushes crowds, the shape, the flange, hits flatly, thinly changes drawability andso on the craft work punching forming flushes, has the significant influence to its ramming aspect size precision