江鈴15米三節臂高空作業車改裝設計（液壓、支腿系統）

江鈴15米三節臂高空作業車改裝設計（液壓、支腿系統）,江鈴15米三節臂高空作業車改裝設計（液壓、支腿系統）,江鈴,15,三節,高空作業,改裝,設計,液壓,系統 附錄A英文部分：The commonly used sources of power in hydraulic systems are pumps and accumulators . Similarly,accumulator connected to atmosphere will dischange oil at atmosphere pressure until it empty. only when connected to a system having resistance to flow can pressure be developed. Three types of pumps find use in fluid-power systems: 1,rotary,2,reciprocating,3,or piston-type,and 3,centrifugal pumps. Simple hydraulic system may use but one type of pump . The trend is to use pumps with the most satisfactory characteristics for the specific tasks involved . In matching the characteristics of the pump to the requirements of the hydraulic system , it is not unusual to find two types of pumps in series . For example , a centrifugal pump may be to supercharge a reciprocating pump , or a rotary pump may be used to supply pressurized oil for the contronls associated with a reversing variabledisplacement pumps . Most power systems require positive displacement pumps . At high pressure , reciprocating pumps are often preferred to rotary pumps . Rotary pumps These are built in many differnt designs and extremely popular in modern fluid power system . The most common rotay-pump designs used today are spurgear , internal gear ,generated rotor , sliding vane ,and screew pumps . Ehch type has advantages that make it most suitable for a given application . Gear pumps Gear pumps are the simplest type of fixed displacement hydraulic pump available . This type consists of two external gear , generally spur gear , within a closed-fitting housing . One of the gear is driven directly by the pump drive shaft . It ,in turn , then drives the second gear . Some designs utilize helical gears ,but the spur gear design predominates . Gear pumps operate on a very simple principle , illustration Fig.7.3 . As the gear teeth unmesh , the volume at the inlet port A expands , a partial vacuum on the suction side of the pump will be formed . Fluid from an external reservoir or tank is forced by atmospheric pressure into the pump inlet . The continuous action of the fluid being carried from the inlet to the discharge side B of the pump forces the fluid into the system . Pressure rise in a spur-gear pump is produced by the squeezing action on the fluid as it is expellde from between the meshing gear teeth and the casing . Fluid from the discharge side is prevented from returing to the inlet side by the clearance between the gears and houseing . Vane pumps The vane pump ,illustration 7.4 , consists of a housing that is eccentric or offset with respect to the drive shaft axis . In some models this inside surface consists of a cam ring that can be rotated to shift the relationship between rotor are rectangular and extend radially from a center radius to the outside diameter of the rotor and from end to end . A rectangular vane that is essentially the same size as the slot is inserted in the slot and is free to slide in and out . As the rotor turns , the vanes thrust outward , and the vane tips track the inner surface of the housing , riding on a thin film of fluid . Two port or end plates that engage the end face of the ring provide axial retention . Centrifugal force generally contributes to outward thrust of the vane . As they ride along the eccentric housing surface , the vane move in and out of the rotor slots . The vane divide the area between the rotor and casing into a series of chambers .The sides of each chamber are formed by two adjacent vanes ,the port or end plates , the pump casing and the rotor . These chambers change in change in volume depending on their respective position about the shaft . As each chamber approaches the inlet port , its vanes move outward and its volume expands , causing fluid to flow into the expanded chamber . Fluid is then carried within the chamber around to the dischange port . As the chamber approaches the discharge port , its vanes are pushed inward ,the volume is reduced , and the fluid is forced out the discharge port . The variable-volume vane pump can be adjusted to discharge a different volume of fluid while running at constant speed , simply by shifting the cam ring with respect to the rotor .When the pump components are in position such that the individual chambers achieve their maximun volume as they reach the inlet port , the maximum volume of fluid will be moved . If the relationship between housing and rotor is changed such that the chambers achieve their minmum of zero volume as they reach the inlet port , the pump delivery will be reduced to zero . Since the vane pump housing or cam ring must be shifted to change the eccentricity and vary the output , variable-displacement vane pumps cannot have the closed end fit common to fixed-displacement vane pumps . Volumetric efficiency is in the range of 90% to 95% . These pumps retain their efficiency for a considerable length of time since compensation for wear between the vane ends and the housing is automatic .As these surfaces wear , the vanes move farther outward from their slots to maintain contact with the housing . Vane pump speed is limited by vane peripheral speed . High peripheral speed will cause cavitation in suction cavity . which results in pump damage and reduced flow . An imbalance of the vanes can cause the oil film between the vane tips and the cam ring to break down , resulting in metal-to-metal contact and subsequent increased wear and slipage . One metheod applied to eliminate high vane thrust loading is a dual-vane construction . In the dual-vane construction , two independent vanes are located in each rotor slot . Chambered edges along the sides and top of each vane from a channel that essentially force causes the vane to follow the contour of each pair of vanes . Centrifugal force causes the vane to follow the contour of the cam-shaped ring . There is just sufficient seal between the vanes and ring without destroying the thin oil film . Piston-type pump Two basic types of piston or reciprocating pumps are the radial piston and the axial typese , both are available as fixed or variable displacement models . Axial piston pumps may be further divided into in-line and bent axis types . All piston pumps operate by allowing oil to flow into a pumping cavity as a piston retreats and then forcing the oil out into another chamber as the piston advances . Design differences among pumps lie primarily in the methods of separating inlet from outlet oil . In-line piston pump The siplest typeof axial piston pump is the swash plate in-line design , illustration 7.5 .The cylinder are connected though piston shoes and a retracting ring , so that the shoes beat anainst an angled swash plate . As the block turns ,the piston shoes follow the swash plate ,causing the piston to reciprocate . The ports are arranged in the valve plate so that the pistons pass the inlet port as they are being pulled out and pass the outlet port as they are being forcing back in . The angle of the swash plate controls the delibery . Where the swash plate is fixed , the pump is of the constant-displacement type . In the variable-displacement , inline piston pump , the swash plate is moumted on a pivoted yoke . As the swash plate angle is increased , the cylinder stroke is increase , resulting in a greater flow . A pressure compensator control can position the yoke automatically to maintain a constant output pressure . Operation of he inline pump compensator control is shown schematically in Fig.7.6 .The control can position the yoke automatically in Fig.7.6 . The control consists of a compensator valve balanced between load pressure and the force of a spring , a yoke piston controlled by the compensator valve to move the yoke , and a yoke retun spring . With no outlet pressure , the yoke return spring moves the yoke to the full delibery position .As pressure builds up ,it acts against the end of the valve spool .When the pressure is high enough to overcome the valve spring , the spool is displaced and oil enters dis placement . If the pressure falls off , the spool moves back , oil is discharged from the piston to the inside of the pump case , and the spring returns the yoke to a greater angle . The compensator thus adjusts the pump output to whatever is required to develop and maintain the preset pressure . This prevents excess power losses bu relief valve operation at full pump volume during holding or clamping . There compensator thus adjusts the pump output to whatever is required to develop and maintain the preset pressure . This prevents excess power losses by relief valve operation at full pump volume during holding or clamping . There is a variation of the swash plate in-line pump . It is a design where the swash plate turns , but the cylinder barrel remains stationary . The plate is canted so that it wobbles as it turns . This action pushes the pistons in and out the stationary cylingder barrel . This type of in-line pump contains a separate inlet and outlet check valve for each piston since the pistons do not move past the inlet and outlet port . BENT-axis piston pump Illustration 7.7 show a bent-axial piston pump , which contatins a cylinder block assembly in which the pistons are equally spaced around the cylinder block axis . Cylinder bores are parallel to the axis . The cylinder block turns with the drive shaft , but at an offest angle . The piston rods are attaached to the drive shaft flange by ball joints . A universal link keys the cylinder block to the drive shaft to maintain alignment and assure that they turn together . The link does not transmit force except to accelerate and decceltate the cylinder block and to overcome resistance of the block revolving in oil filled housing . As the shaft roates , distance between any one piston and the valving surface changes continually . Each piston moves away from the valving surface during one half of the revolution and toward the valving surface during the other half . The inlet chamber is in line as the pistons move away , and the outletr chamber is in line as the pistons move closer , thus drawing liquiring in during one half of the inlet chamber as the pistons are moving away from the pintle . Thereforce , during rotation , pistons draw liquid into the cylinder bores as they pass the inlet side of the pinntle and force that liquid out of the bores as they pass the outlet side of the pintle . The displacement of this pump varies with the offset angle , the maximum angle being 30 degree ,the minimum zero . Fixed displacement models are usually avaiable with 23 degree angle .In the variable displacement construction a yoke with an external control is used to change the angle . With some contronls , the yoke can be moved over center to reverse the direction of flow from the pump . Pump/system interaction Frequently , hydraulic system designers choose off-the-shelf pumps with little cocern other than supplying sufficient flow at available input power . Early enphasis that positive displacement pumps supply only flow and that pressure is developed by the system suggests that , as a minmum , the pump should be chosem in light of several overall requirements and with system detailed design and the nature of the working fluid well in mind . Positive displacement pumps generate flow . In a fixed delivery pump , provisions must be made to dissipate flow or system pressure will rise until a rupture occurs . The usual means of accomplishing flow control is to place a relief valve inthe high pressure line . When the pressure rise above an established amoumt ,the relief valve will vent excess flow back to the reservoir . In such systems , pump flow and relief valve capacity must be carefully matched to assure proper venting . Flow from a high pressure line through a relief valve to a low pressure element is wasted hydraulic horsepower , which can be calculated from the following relationship : hp=PQ/1714 Where : Q = flow in gpm This wasted horsepower is converted to heat in the hydraulic system . If not properly removed , the heat can damage the fluid , elastomer seals , and other organic material in the system . Pressure-compensated variavle delivery pumps do not require a relief valve in the high pressure line . The pressure compensation feature eliminates the need for the relief valve . In nearly all working systems ,however , at least one is used on just-in-case basis . The use of a pressure compensator , while avoiding dependence on a relief valve , brings on its own problems . The actuator -spring-spool arrangement in the compensator is a dynamic , damped-mass-spring arrangement . However , when the system calls for a chang in axhieve their maxmum volume as they reach the inlet port , the maximum volume of fluid will ve moved . If the relationship between housing and rotor is changed such that the chambers achieve their minimum of zero volume as they reach the inlet port , the pump delivery will be reduced to zero . Since the vane pump housing or cam ring must be shifted to change the eccentricity and vary the output , variable-displacement vane pumps cannot have the closed end fit common to fixed-displacement pumps . Volumetric efficiency is the range of 90% to 95% . These pumps retain their efficiency for a considerable length of time since compensation for wear between the vane ends and the housing is automatic . As these surfaces wear , the vanes move farther outward from their slots to maintain contact with the housing . Vane pump speed is limited by vane peripheral speed . High peripheral speed will cause cavitation in suction cavity , which results in pump damage and reduced flow . An imbalance of the vanes can cause the oil film between the cane tips and the cam ring to break down , resulting in metal-to-metal contact and subsequent increased wear and slipage . One method applied to eliminate high vane thrust loading is a dual-vane construction . In the dual-vane construction , tow independent vanes are located in each totor slot chmbered edges along the sides and top of each vane from a channel that essentially balances the hydraulic pressure on the top and bottom of each pair of vanes . Centrifugal force cause the vane to follow the contour of the cam-shaped ring .There is just sufficient seal between the vanes and ring without destroying the thin oil film . 附錄B中文部分：常用的液壓系統的動力源是泵和蓄能器。一般情況下，一個蓄能器在正常的大氣壓力下，連續的向各系統中壓入液壓油，直至將所儲存的能量全部用完為止。 只有當其連接的系統中，具有抗流壓力時才能夠得到補充。在液壓系統和液力系統中，常使用液壓泵有三種類型： 1、回轉式， 2、往復式， 3、活塞式或者離心式。 簡單液壓系統一般使用的都是第一類液壓泵。 目前的發展趨勢是針對具體的工作任務和工況，選用最佳的液壓泵類型。在符合特性和要求的液壓泵中，找到兩種不同類型的液壓泵式很常見的。 例如，離心泵，往復泵都可以可對系統增壓，旋轉泵和變量液壓泵聯合使用也可以提供高壓的液壓油。 大部分動力系統還需要采取容積式液壓泵泵。而在較高的體統壓力下，往復泵往往要優于回轉泵。 回轉泵這些形式的液壓泵因?yàn)榫哂性S多不同的設計形式而極受歡迎，在現代流體動力系統。 最常見的旋轉泵的設計形式，包括內部使用齒輪的、內部使用轉子的、內部采用滑動葉片的和使用螺桿的。 其中，每一種類型都有其獨特的優點，都有其最適合的一定的應用場合。 齒輪泵齒輪泵是可以提供的最簡單的一種液壓泵。 這一類型的液壓泵一般包括兩個外嚙合的齒輪，一般是圓柱直齒輪，安裝在一個密封的殼體里面。 其中一個齒輪由液壓泵的傳動軸直接驅動， 第一個齒輪然后再推動第二輪。還有一些設計中利用螺旋齒輪，但是一般以齒輪設計為主。 齒輪泵的動作的原理非常簡單，如插圖7.3 所示。 由于在齒輪的輪齒在脫開嚙合時，進氣道擴大， 液壓泵將會形成局部真空的具有吸力的空腔。 流體在系統的壓力下被從外部油箱或罐體中壓入， 連續運動的液壓油在液壓泵的作用下，從真空的吸力空腔中被送入排出液壓油的一側B側。直齒輪泵內的液壓油被從脫開嚙合的輪齒和套管之間不斷的排出，這種擠壓運動使得齒輪泵內的壓力上升，從排油一側來的液壓油由于被阻止，不能返回進油一側的輪齒的間隙和空腔。 葉片泵如插圖7.4所示，葉片泵一般是由一個相通的腔體，是偏心或抵消對傳動軸軸線。在一些模型內的表面設有一個凸輪環，一個可旋轉移動的長方形的轉子，轉子的徑向延長，從一個中心，半徑為外徑的轉子，到末端結束。 上面是尺寸大小相同的插槽，矩形葉片一般插入到插槽中，并且可以自如的滑入和滑出。 當轉子轉動時，葉片被向外甩出， 而葉片尖端則貼緊其運動軌道空腔的內表面， 處于液壓油的薄膜的上面。 兩個油口或端板，向環形的端面提供軸向的存儲。 通常離心有助于葉片的向外推出。當葉片處于偏心空腔的表面上時，葉片從轉子的縫隙中甩出和甩。 葉片將套管和轉子之間的區域分成一系列的小空腔。每一個小空腔都是由兩個相鄰葉片，油口或者端盤，液壓泵殼體和轉子形成。 這些空腔的容積的變化取決于他們相對于軸的相對位置。當每個廳內靠近進內氣孔的時候，其葉片向外移動，其空腔的容積膨脹， 造成液壓油流入擴大空腔。 流體隨后被帶入圍繞著排油孔的空腔內。當這些空腔靠近排油孔時，葉片被甩入腔內，空腔的容積減小，液壓油隨即被壓出排油孔。變量葉片泵，可以進行調整，以適應不同的流體排量，當在定常速度下運行時， 只需要改變把凸輪環相對于對轉子的位置即可。當液壓泵的部件的處于各自的空腔在靠近吸油孔時達到最大的位置的時候，流體的最大排量就將會改變。 如果腔體和轉子的相對關系改變，則空腔在他們到達吸油孔的時候就達到了他們的最小容積零容積，此時，液壓泵的排油量也減少到零。由于葉片泵的空腔或凸輪圈必須變化從而改變偏心率即改變輸出量， 變量葉片泵沒有相應于普通固定位移葉片泵的固定端， 容積效率范圍是90%至95% 。 這些液壓泵能夠在一個相當長的時間里保持其效率，因?yàn)槿~片兩端和空腔之間摩擦補償是自動的。 正是由于這些表面的摩擦， 才使得葉片泵的葉片能夠向外面甩出同時又不會脫離插槽。葉片泵的速度一般要受到葉片圓周速度的限制。 過高的圓周速度將導致空腔內出現負壓，從而導致液壓泵損壞和流量減小。 一個不平衡的葉片將會引起葉片頂端和凸輪環之間的油膜的破壞，從而進一步導致金屬和金屬之間的直接接觸，因而增加了磨損和葉片泵的動力傳動損耗 。消除這種葉片泵的葉片的高推力負荷的方法之一就是采用雙葉片結構。在雙葉式結構中，每?jī)蓚€(gè)互相獨立的葉片是分別設置在每個轉子槽中的。腔室的邊緣兩旁和頂部葉片每一個渠道，基本上形成了一個十字狀，每個一雙葉片等高。 在離心力的作用下，使得葉片隨著凸輪環的外部輪廓的變化而變化。 當葉片和凸輪環之間形成了足夠大的間隙的時候，將會破壞油膜。 活塞式泵兩種基本類型的活塞液壓泵或者是往復式液壓泵都是活塞徑向和軸向類型的， 兩者均可作為定量泵或可變排量泵模型。 其中，軸向柱塞泵，又可以進一步分為線性柱塞泵和彎曲軸型柱塞泵兩種類型。 所有的活塞式液壓泵的運行原理，都是通過液壓油流入泵腔而推動活塞向后面移動，然后活塞再向前移動，從而將液壓油排出，使得液壓油進入泵的另一個腔室中。 不同的泵的設計差異泵主要在于活塞進入和推出從而將液壓油分離的方法。直軸式柱塞泵最簡單的軸向柱塞泵是將沖板進行線性化設計，如插圖7。5 所示，氣缸與活塞的回縮盤之間相連， 使移動的回縮盤成傾斜式。 當傾斜圓盤轉動的時候，柱塞的端腳斜盤上運動，從而使得活塞桿不斷的往復的運動，同時因?yàn)橛涂诜謩e安排在閥板上，能夠使活塞通過進氣道，當它們運動到一定的位置時，通過油口將液壓油推出排油口。 斜盤的傾斜角度決定了柱塞泵的排量。在這里，斜盤的位置是固定的，而泵的位移是恒定的。 在變量的線性柱塞泵中，逆止閥活塞泵，沖板是裝在一個鉸鏈的枷鎖。 由于沖板角度的增大，氣缸沖程增加，形成了更大的流量。 由于壓力補償控制位置的作用，自動保持恒定輸出壓力。 線性柱塞泵的運行原理就是如插圖7.6所示 。 在圖中，能夠自動的控制枷鎖的定位。 這種控制由一個補償閥來平衡負載壓力和系統的壓力，枷鎖活塞由補償閥移動另一個枷鎖來實現控制。 由于壓力無法卸載， 枷鎖回位彈簧的推動枷鎖直到臨界的位置。 由于壓力的累積，它的動作是組織閥芯末端。當壓力高至足以克服閥的彈簧力的時候，閥芯就會變換位置，同時，液壓油也會進入原來的空腔中。假如壓力下降，閥芯向后移動， 液壓油被活塞排出而進入液壓泵的管道。系統就會使枷鎖回到一個更大的角度。補償器調節泵的輸出量，從而達到任何要求達到的更高的壓力或者保持原來預置的壓力。這使得過剩的動力損失得以通過節流閥的在滿載的時候的保持和收緊作用而被部分保留和利用。 在直軸式的柱塞泵中，有一個可以變化的斜盤。 這是一個設計中的斜盤式的轉折，但缸筒依然保持了其平穩。 斜板是傾角回轉的。 這一動作推動活塞進入和推出較為平穩的缸筒。 這種類型的直軸式柱塞泵在每一個位置上都包括一個單獨的進油口檢測閥和一個單獨的出油口檢測閥。因此，柱塞才不會在移動的時候超出進油口和排油口。 斜軸式柱塞泵如圖7.7所示，說明了斜軸式柱塞泵的工作原理， 裝配中的活塞包含缸體也同樣以缸體的軸線為基準間隔排列在四周， 缸孔平行于軸線。活塞棒通過法蘭盤和球關節連接在傳動軸上。一個普遍的鏈接鍵缸體的傳動軸一定要保持對準，并且要保證他們一起轉 。缸體和克服阻力的旋轉座因?yàn)榧铀俨粋鬟f力矩而使得液壓油充入空腔。 同時，由于軸的旋轉，其距離任何一個活塞和閥門表面的距離在不斷變化。 每個活塞逐漸遠離閥門的表面，直到達到總路程的一半時產生了質的變化。進油室是呈線性的遠離線為活塞， 而出油室則是線性的向活塞靠攏， 因此所繪制出的流體都是在進氣道空腔內的中間處遠離活塞 。這一期間，活塞輪換提取液壓油進入缸孔，他們通過進氣道的一側和高壓力使液壓油流出鉆孔，同時，它們通過插座一側的樞軸，這種泵的位移隨著偏移角的變化而變化， 其最大角度為30度，最低為零。 固定位移模式通常每周以23度的傾角。 在變排量施工的枷鎖與外聘 控制是用來改變角度。 一些控制，枷鎖可以移到中心逆向流動的方向由泵。 泵/系統頻繁互動 液壓系統設計者選擇現成的水泵幾乎關于除供應足夠的流量，可輸入功率。在早期的液壓泵的結構中，正位移泵供應只有流量和壓力是由系統顯示， 作為最小的一個， 泵應選擇參照若干總體要求和系統的詳細設計和性質 工作流體好記。 正位移泵產生的流量。 在一個固定輸送泵， 必須作出規定，以分散水流或系統的壓力將上升，直至出現破裂。 通常的辦法實現流量控制，是把一個閥耐高壓線路。 當壓力超過既定額度，溢流閥會發泄過?；亓鲙靺^(qū)。 在這種制度下，泵的流量和閥容量必須仔細匹配，以保證適當?shù)男埂?液壓油的液流從高壓線路通過溢流閥，以直到液壓馬達，變成了低氣壓?？梢杂?jì)算出這一過程服從以下關系:hp= pq/1714這里: q=油路中的流量液壓系統中由于電流階躍引起部分能量被轉化為熱量二浪費掉了。 如果不妥善解決，熱量會破壞液壓系統、油管、橡膠密封件，和其它有機物質的東西。 壓力補償式變量泵不需要在高壓線路安裝溢流閥。 壓力補償功能也不需要安全閥。 在幾乎所有的工作系統中，一般至少有一個是用屬于特殊的情況。 使用壓力補償，同時避免依賴溢流閥而帶來的系統本身的問題。 動力-彈簧閥芯排列中的補償是動態的，即阻尼-彈簧-安裝排列。其落點量達到進氣道， 最高流體體積就能夠達到。 如果空腔和轉子之間的關系發生了改變，空腔會調整自己的流量，其最低流量一般為零。當葉片到達進氣道時，液壓泵的輸送量將減少到零。 由于葉片泵住房或凸輪圈必須轉向改變偏心率和不同的輸出， 可變位的葉片泵沒不能有封閉式，如果需要封閉式，則需要選用普通的固定泵。葉片泵的容積效率范圍為90%至95% 。 這種液壓泵能夠保留其高效率達到相當長的時間，因?yàn)槿~片兩端和空腔之間的補償磨損是自動的。正是由于這些表面磨損，當葉片處于遠離其插槽的位置時，才能夠保證葉片與葉片之間的空腔。 葉片泵的速度是有限的，其速度決定于葉片轉動時的圓周速度。 過高的圓周速度將導致空腔內產生負壓，從而導致液壓泵的損壞，也會導致流程的縮短。一個失去平衡的葉片能造成葉片的尖端和凸輪環之間的油膜被破壞，從而導致金屬和金屬的直接接觸，因而增加了磨損和動力傳遞的損耗。用于消除高壓葉片的推力負荷的一種方法就是采用雙葉片構造。在雙葉式構造中， 每一片獨立的葉片設置在相應的每個飛輪插槽的邊沿線兩側和頂部之間。離心力造成葉片隨著凸輪形盤的輪廓轉動、變化。因此能夠有足以密封性能， 葉片之間的薄油膜也不會被破壞。